Cub Cadet 5264D Checking TRANSMISSION/HYDRAULIC System OIL Level, Hydraulic System Filter Part No

Page 32

CHECKING TRANSMISSION/HYDRAULIC SYSTEM OIL LEVEL

Check the hydro transmission/hydraulic system oil level before each use. NOTE: Check the oil level only while the engine is stopped and the tractor is standing on a level surface.

The oil level sight glass is located in the rear of the transmission housing, just to the right of the rear PTO shaft. Refer to Figure 42.

The oil level is okay if oil can be seen through the sight glass. If the level is below the sight glass, oil must be added to the transmission as follows:

•Locate the oil fill plug on the upper right of the rear of the transmission housing. See Figure 42.

OIL FILL PLUG

OIL LEVEL

S IGHT

HOLE

Figure 42

•Clean the area around the oil fill plug to prevent debris from entering the transmission housing.

•Turn the oil fill plug counterclockwise to unscrew from the transmission housing.

•Insert a funnel (preferably with a flexible spout) into the fill hole of the transmission housing.

•Add Cub Cadet Drive System Plus oil until the oil level can be seen through the sight glass. Do not overfill the transmission.

IMPORTANT: Always use Cub Cadet Drive System Plus oil to ensure correct formulation. Substitute oils could affect performance and may cause damage to the transmission.

•Reinsert the oil fill plug into the transmission housing and turn clockwise until tight.

CHANGING THE HYDRO TRANSMISSION AND HYDRAULIC SYSTEM OIL FILTERS

With the exception of the first oil filter change after the 25 hour break-in period, the hydraulic system oil filter should be changed along with the transmission/hydraulic system oil after every 200 hours of operation. The hydro transmission filter should be changed after every 100 hours of operation.

25 Hour Break-In Period Filter Change

During the initial hours of tractor operation, contaminants caused by the normal break-in of internal transmission and hydraulic system components will collect in the oil filters. Because of this, both the hydro transmission and hydraulic system filters should be changed after the first 25 hours of operation.

Hydro Pump Filter — Part No. BS-492392S

Hydraulic System Filter — Part No. 723-3014

NOTE: If a front end loader, or a loader and back- hoe, is installed on the tractor after the first 25 hours of operation, it is recommended that the fil- ters again be changed after the first 25 hours of operation with these attachments installed.

Changing Hydro Transmission Oil Filter

The hydro transmission oil filter should be changed after the first 25 of tractor operation, and after every 100 hours operation.

•Stop the tractor engine and lower the mower deck or any other hydraulically lifted implement to the ground.

•Slide the seat fully forward; then tilt seat forward.

•Through the access hole in the rear fender, clean the area around the hydro transmission oil filter to prevent debris from entering the hydraulic system. Refer to Figure 43.

•Stuff shop rags underneath the hydro transmis- sion filter to absorb any lost oil when the filter is removed. Refer to Figure 43.

 

HYDRO

ACCESS HOLE

TRANSMISSION

FILTER

IN FENDER

 

Seat Removed for Clarity

Figure 43

•Apply a light coating of clean transmission oil to the gasket of the new hydro transmission filter.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTo the Owner Table of ContentsCalling Service Information Recording Model and Serial Number Information Rops Information PlateImportant Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops ServiceChildren Operating the PTOPage Safety Labels Battery Warning Label Located Under HoodFAN Warning Label Located on Each Side of Radiator PTO Warning Label Located on Rear PTO ShieldControls and Features PTO Switch Ignition SwitchSteering Wheel Throttle HandleSeat Adjustment Lever PTO Reverse Override SwitchHand Holds Transmission 4WD Shift LeverHazard Light Switch Headlight SwitchDifferential Lock Pedal Foldable Rops Rollover Protective StructureBattery Indicator Light Oil Pressure IndicatorPTO Engaged Indicator Brake Engaged IndicatorSafety Interlock System OperationRollover Protective Structure Rops Folding the RopsStarting the Engine NEW Tractor BREAK-IN ProceduresFueling the Tractor Using Jumper Cables to Start Engine Cold Weather Starting below 14 FStopping the Engine Driving the TractorUsing the Forward and Reverse Pedals Using the HI/LO Range Shift LeverLOW Stopping the TractorDriving on Slopes Using the Differential Lock PedalUsing the 4WD Shift Lever Using the Hydraulic Lift Lever Using the PTO Reverse Override SwitchEngaging the PTO LightingUsing the TOP Link Retainer Hook Using the Three Point HitchHazard Lights Removing the Rear PTO CoverUsing the Hitch Plate Tractor WeightingFront Weights Weighting the Rear of the TractorAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes General Information MaintenanceLubrication Table Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageAzard Bulb Replacement Servicing Electrical SystemMain Fuse Never use a higher amperage fuseAccessing the Lower Dash Panel Area Electrical Circuit RelaysRight Side Left SideChecking TRANSMISSION/HYDRAULIC System OIL Level Hydraulic System Filter Part NoChanging Hydraulic System Filter Changing the Hydro Transmission and Hydraulic System OILChanging Front Axle and Final Reduction Gear Case OIL Check Front Axle OilCheck Final Reduction Gear Case Oil Wheel LUG NUT Torque Lubrication of Drive ShaftLubrication of FWD Drive Shaft Tire Maintenance Maintenance of the Rollover Protective Structure RopsTractor Storage Removing the Tractor from StorageEngine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageIgnition System Engine Maintenance Cleaning the Engine Cleaning the Radiator SCREEN/RADIATORChecking Engine OIL Level Adding Engine OILChanging the Engine OIL and Filter Changing the Engine Coolant Checking Engine Coolant LevelInspection of Cooling System Hoses Changing the AIR Cleaner Changing The Fuel Filter Servicing the Fuel FilterDraining The Fuel Filter Specifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberU.S.A Canada
Top Page Image Contents