Cub Cadet 23HP service manual Changing the Spindle Assembly, Adding Hydraulic Oil use SAE20W

Page 16

Cover

Plate

Spindle

Figure. 7

blade drive belt from the pulley and slide the belt away from the pulley.

d.Remove tension of the PTO belt by moving the belt tensioning rod. Loosen the belt retaining bolt.

e.Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt.

f.Reverse the process to install the belt.

Note: When replacing belts do not over- tighten. Adjust the idler pulley so that a ten- pound pull with a spring scale between two pulleys deflects the belt about 1/2".

4.Changing the Spindle Assembly

a.Jack up the front of the mowing deck about one foot and block it in that position.

b.Make sure the blade clutch is disengaged.

c.Remove the deck cover.

d.Remove the drive belts. (See 3. Changing Blade Drive Belts.)

e.Remove the cutter blade. (See 2. Chang- ing a Blade.)

f.Using a wrench or socket rachet remove four hex nuts, and the four hex head cap screws. Remove the spindle assembly.

B.Hydraulic Oil

WARNING:

Never overfill the hydraulic units. Damage can occur if the oil level is not within the proper operating range.

Note: When adding hydraulic oil, do so in

small quantities and recheck the oil level before adding more. It is important that you do not overfill the reservoir.

Figure. 8

Hydraulic Tank

1.Adding Hydraulic Oil (use SAE20W 50)

a.Place the Mower on a level surface and engage the parking brake.

b.Stop the engine and remove the key from the ignition switch.

c.Clean the area around the Hydraulic Oil fill neck.

d.Remove the hydraulic fill cap and check the level. The correct level is up to the low- est hole of the oil tank fill neck.

e.Pour hydraulic oil into the reservoir up to the lowest hole in the oil tank fill neck, if necessary.

2.Draining Hydraulic Oil

Used hydraulic oil must be disposed of properly. Do not pour it down a drain or sewer, or dump it on open land, this creates an environmental hazard. Please be aware of the environment when disposing of used oil.

a.Place the Mower on a level surface and engage the parking brake.

b.Stop the engine and remove the key from the ignition switch.

c.Remove the mower deck. See Mower Deck on page 13.

d.Raise the seat forward to expose the hydraulic oil fill point.

e.Clean the area around the hydraulic fill oil cap.

f.Remove hydraulic fill oil cap.

g.Place a suitable container (at least 2 gal- lon) under the hydraulic reservoir and filter.

h.Remove the hydraulic filter to allow hydrau- lic oil to drain. Remove the drain plug from the bottom of the hydraulic oil tank to drain. Replace the plug.

i.Place a small pan under the skid plate. Remove fill oil cap from hydraulic reservoir for faster drainage. Remove nut caps and

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Hydrostatic Zero-Turn Riding Mower Table of Contents Forward Safety Precautions General Safety OperationsGeneral When Mowing Related to FuelSafety Decals and Labels Shield Missing do not OperateSpecifications Safety Awareness when Mowing When MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Initial Adjustments Check the fluid levels and tiresZero Turn Break-In And Operating Procedures Lubricate all fittings listed in the mainte- nance sectionOrientation Initial OperationStart the Engine Maintenance Service Mower DeckParking the Mower Removing the Mower DeckChanging a Blade Changing the Blade Drive BeltsChanging the Spindle Assembly Stop the engine and remove the key from the ignition switchHydraulic Oil Adding Hydraulic Oil use SAE20WBattery Removal Installing the BatteryElectrical Circuit Specific Gravity Freezing Temp FPage Brakes TiresInflation Pressure Hydraulic System Hydraulic Oil Tank and FilterStorage Maintenance Schedule OIL Chart If Mower is so equippedHigh Speed Tracking Adjustment Enginge RPM Check and AdjustmentDeck Center Anti-Scalp Roller Settings Deck Corner Ball Wheel Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Equipment TWO-YEAR Limited Warranty

23HP specifications

The Cub Cadet 23HP lawn tractor is a powerful and efficient machine designed for homeowners looking to maintain their lawns with ease. This lawn tractor offers a blend of performance, comfort, and innovation, making it a top choice for both small and medium-sized yards.

At the heart of the Cub Cadet 23HP is its reliable engine. The 23 horsepower engine provides ample power to tackle tough mowing conditions and hilly terrains effortlessly. The engine is designed for optimal performance, ensuring that the tractor operates smoothly under various conditions. With a reliable starter system, getting the tractor running is quick and efficient, allowing users to get to work without delay.

One of the standout features of the Cub Cadet 23HP is its innovative cutting deck. The 46-inch or 54-inch cutting deck options are designed for precision and efficiency, providing an excellent cut quality while reducing the time spent mowing. The deck is equipped with adjustable cutting heights, allowing users to customize their lawn care to match their specific needs. This adaptability ensures that the mower can handle different grass types and lengths with ease.

Comfort is another key characteristic of the Cub Cadet 23HP. The tractor features an adjustable high-back seat that provides support during long mowing sessions. Its ergonomic design ensures that users can maintain a natural posture while operating the tractor, reducing fatigue. The steering wheel is also designed for ease of use, allowing for smooth maneuverability even in tight spaces.

In terms of technology, the Cub Cadet 23HP comes equipped with advanced features that improve user experience. The LED headlights provide excellent visibility for early morning or late evening mowing. Additionally, the tractor features a dashboard with clear gauges that keep users informed about fuel levels, engine temperature, and other essential metrics.

Safety is a priority with the Cub Cadet 23HP. The tractor is equipped with safety features such as a seat switch that ensures the mower stops when the operator leaves the seat. This feature reduces the risk of accidents and enhances overall safety during operation.

Overall, the Cub Cadet 23HP lawn tractor combines power, comfort, and cutting-edge technology to deliver an exceptional mowing experience. Whether you have a small backyard or a larger property, this lawn tractor is designed to meet a variety of landscaping needs efficiently, making lawn care a hassle-free task. With its robust build and thoughtful features, the Cub Cadet 23HP is an investment in maintaining a beautiful lawn.
Top Page Image Contents