Cub Cadet 23HP Deck Corner Ball Wheel Roller Settings, Deck Center Anti-Scalp Roller Settings

Page 25

C. Deck Corner Ball Wheel Roller Settings

1.Matching the set heights of the ball rollers on the four corners of the mower deck to the desired cut height will prevent edge scalping and minimize any side-to-side variance in cut height.

2.There are three height adjustment holes in the bracket that mount the ball rollers to the deck.

a.Use the top set of holes for cut heights of 2 inches or lower.

b.Use the middle set of holes for a 2-1/2 - 3-1/2 inch cut height.

c.Use the bottom set of holes for cut heights of 4 inches or higher.

D.Deck Center Anti-Scalp Roller Settings

1.The front and rear rollers help prevent the scalping of high spots and uneven terrain across the center section of the deck.

2.The rollers on the front of the deck are fixed at the factory and can not be adjusted.

3.The rollers on the rear of the deck can be adjusted downward one inch.

a.Lowering the roller will increase the strip- ing effect left behind the mower.

b.This positioning of the rear roller will also help to filter the mulched grass clippings into the turf.

c.Roller should not be lowered if the cut height is set at 2-1/2 inches or lower.

E.Lap Bar Adjustment

1.Proper lap bar and seat adjustment will result in the following:

a.In the neutral position with hands on the lap bars,

1.Operator’s upper arms should be relaxed and approximately vertical.

2.Operator’s forearms should be approxi- mately vertical.

b.In the full forward position,

1.Operator’s back should stay in contact with the seat back.

2.Lap bars should not contact operator’s legs.

c.In the full reverse position,

1.Lap bars should not contact the opera- tor’s legs or torso.

2.Set the seat to the preferred operating position.

a.Adjustment lever is located under the front edge of the seat.

b.The seat has five inches of front-to-rear adjustment available.

4.Check factory settings of lap bars for the con- ditions listed above.

Note: If lap bar adjustments are required,

height adjustments should be made prior to angular adjustments.

5.To adjust the height of the lap bars,

a.Remove the nuts from the lap bar mounting bolts (see Fig. 11).

b.Remove the bolts and lap bar and repostion to the seconc set of holes in the mounting block.

c.Replace the bolts and nuts and tighten to 28-34 ft-lbs.

1.If angular adjustments are also required, nuts can be tightened until snug at this point.

d.The same adjustments should be made to both sides of the mower.

6.(Optional lapbars only) To adjust the front-to- rear angle of the lap bars,

a.Loosen the nuts on the lap bar mounting bolts, leaving the bottom one fairly snug.

b.The top hole is slotted, allowing the lap bar to pivot on the bottom bolt.

c.Move lap bar to the desired angle and tighten the nuts to 28-34 ft-lbs.

Note: In the neutral position, the handles of

the lap bars should be aligned with approxi- mately a one inch gap between the tips. Adjus- the gap by adding shim washers to the top mounting bolt between the lap bar and the mounting block.

d.Check the results of any adjustments to the conditions described in section a, above. Repeat any adjustment procedures as required until all conditions are met.

Figure. 11

Lap Bar Mounting Bolt and Nuts

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Hydrostatic Zero-Turn Riding Mower Table of Contents Forward Safety Precautions General Safety OperationsGeneral Related to Fuel When MowingShield Missing do not Operate Safety Decals and LabelsSpecifications Safety Awareness when Mowing When MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Check the fluid levels and tires Initial AdjustmentsLubricate all fittings listed in the mainte- nance section Zero Turn Break-In And Operating ProceduresOrientation Initial OperationStart the Engine Mower Deck Maintenance ServiceParking the Mower Removing the Mower DeckChanging the Blade Drive Belts Changing a BladeStop the engine and remove the key from the ignition switch Changing the Spindle AssemblyHydraulic Oil Adding Hydraulic Oil use SAE20WInstalling the Battery Battery RemovalElectrical Circuit Specific Gravity Freezing Temp FPage Brakes TiresInflation Pressure Hydraulic Oil Tank and Filter Hydraulic SystemStorage Maintenance Schedule If Mower is so equipped OIL ChartEnginge RPM Check and Adjustment High Speed Tracking AdjustmentDeck Center Anti-Scalp Roller Settings Deck Corner Ball Wheel Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Equipment TWO-YEAR Limited Warranty

23HP specifications

The Cub Cadet 23HP lawn tractor is a powerful and efficient machine designed for homeowners looking to maintain their lawns with ease. This lawn tractor offers a blend of performance, comfort, and innovation, making it a top choice for both small and medium-sized yards.

At the heart of the Cub Cadet 23HP is its reliable engine. The 23 horsepower engine provides ample power to tackle tough mowing conditions and hilly terrains effortlessly. The engine is designed for optimal performance, ensuring that the tractor operates smoothly under various conditions. With a reliable starter system, getting the tractor running is quick and efficient, allowing users to get to work without delay.

One of the standout features of the Cub Cadet 23HP is its innovative cutting deck. The 46-inch or 54-inch cutting deck options are designed for precision and efficiency, providing an excellent cut quality while reducing the time spent mowing. The deck is equipped with adjustable cutting heights, allowing users to customize their lawn care to match their specific needs. This adaptability ensures that the mower can handle different grass types and lengths with ease.

Comfort is another key characteristic of the Cub Cadet 23HP. The tractor features an adjustable high-back seat that provides support during long mowing sessions. Its ergonomic design ensures that users can maintain a natural posture while operating the tractor, reducing fatigue. The steering wheel is also designed for ease of use, allowing for smooth maneuverability even in tight spaces.

In terms of technology, the Cub Cadet 23HP comes equipped with advanced features that improve user experience. The LED headlights provide excellent visibility for early morning or late evening mowing. Additionally, the tractor features a dashboard with clear gauges that keep users informed about fuel levels, engine temperature, and other essential metrics.

Safety is a priority with the Cub Cadet 23HP. The tractor is equipped with safety features such as a seat switch that ensures the mower stops when the operator leaves the seat. This feature reduces the risk of accidents and enhances overall safety during operation.

Overall, the Cub Cadet 23HP lawn tractor combines power, comfort, and cutting-edge technology to deliver an exceptional mowing experience. Whether you have a small backyard or a larger property, this lawn tractor is designed to meet a variety of landscaping needs efficiently, making lawn care a hassle-free task. With its robust build and thoughtful features, the Cub Cadet 23HP is an investment in maintaining a beautiful lawn.
Top Page Image Contents