Cub Cadet 23HP service manual High Speed Tracking Adjustment, Enginge RPM Check and Adjustment

Page 24

Performance Adjustments

A. High Speed Tracking Adjustment

If mower tracks to one side with both lap bars in fully forward position:

1.Check air pressure in all four tires:

a.Pressure should be within specified ranges and balanced side-to-side.

b.Rear tires 8-10 psi. recommended (20 psi MAX.)

c.Front tires 20-25 psi. recommended (40 psi MAX.

2.Check hydraulic fluid level (Ref. Engine owner’s manual)

3.Verify that the mower does not creep when the engine is running, the lap bars are in the neutral position and the parking brake is released. (Refer to section D-3 on page 19 of this manual if this condition exists).

4.Recheck the tracking after any adjustments based on the above.

5.If uneven tracking persists, adjust as follows. (see Fig. 10)

a.Unit tracks to the RIGHT, adjust Left lap bar stop bolt to make it longer.

b.Unit tracks to the LEFT, adjust Right lap bar stop bolt to make it longer.

6.Re-check the tracking and make any fine tun- ing adjustments to the lap bar stop bolts as required.

Note: If stop bolt is adjusted too far, track-

ing problem will change sides. Make the fine tuning adjustments by shortening the same bolt.

Figure. 10

Lap Bar Stop Bolt

B. Enginge RPM Check and Adjustment

Description

High RPM Spec.

Low RPM Spec.

 

 

 

 

 

 

23 HP Kohler

3750 +/-75

1650 +/-100

 

 

 

NOTE: RPM Specs. are for free running engines under no load.

1.Verify that the lap bars are in the neutral posi- tion, the parking brake is on, and the PTO drive is disengaged.

2.Start the mower and let it run at approximately half throttle for 3-5 minutes to bring the engine up to operating temperature.

3.Locate the Hour Meter/Tachometer/ Service Minder display on the right hand operator con- trol panel. (see Fig.1 on page 8 of the manual) This display defaults to Tachometer mode when engine is running.

4.Move the throttle lever to the high speed posi- tion and note the RPM reading on the display.

5.Move the throttle lever back to the low speed position and again note the displayed RPM’s.

6.Compare these noted RPM readings to the specifications in Table 1, for the engine that is on your mower.

7.If the readings do not correspond to the ranges in the table, refer to the engine owner’s manual for the proper adjustment pro- cedures.

8.If adjustments per the engine operator’s man- ual do not result in proper RPM readings, con- tact your service technician.

9.Note: The throttle cable sheath may shrink or slip over time, changing the relationship between the throttle lever on the left hand operator control panel and the throttle arm on the engine. To readjust the throttle cable:

a.Make sure the engine is off, place lap bars in the neutral position, set the parking brake, and disconnect and ground both of the spark plug wires.

b.Locate and loosen the cable clamp on the engine throttle plate.

c.Place the operator’s throttle lever to the high speed position and then slide the cable through the clamp until the throttle arm is in the full throttle position. (Ref. Engine owner’s manual)

d.Tighten the cable clamp.

e.Move the operator’s throttle lever between high and low speed and verify that the engine throttle arm also moves through it’s full range of motion.

f.Repeat as required to obtain proper throt- tle adjustment.

g.Verify proper throttle adjustment by check- ing RPM readings as outlined above.

24

Image 24
Contents Hydrostatic Zero-Turn Riding Mower Table of Contents Forward General Safety Operations Safety PrecautionsGeneral When Mowing Related to FuelSafety Decals and Labels Shield Missing do not OperateSpecifications When Mowing Safety Awareness when MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Initial Adjustments Check the fluid levels and tiresZero Turn Break-In And Operating Procedures Lubricate all fittings listed in the mainte- nance sectionOrientation Initial OperationStart the Engine Maintenance Service Mower DeckParking the Mower Removing the Mower DeckChanging a Blade Changing the Blade Drive BeltsChanging the Spindle Assembly Stop the engine and remove the key from the ignition switchHydraulic Oil Adding Hydraulic Oil use SAE20WBattery Removal Installing the BatteryElectrical Circuit Specific Gravity Freezing Temp FPage Tires BrakesInflation Pressure Hydraulic System Hydraulic Oil Tank and FilterStorage Maintenance Schedule OIL Chart If Mower is so equippedHigh Speed Tracking Adjustment Enginge RPM Check and AdjustmentDeck Corner Ball Wheel Roller Settings Deck Center Anti-Scalp Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Equipment TWO-YEAR Limited Warranty

23HP specifications

The Cub Cadet 23HP lawn tractor is a powerful and efficient machine designed for homeowners looking to maintain their lawns with ease. This lawn tractor offers a blend of performance, comfort, and innovation, making it a top choice for both small and medium-sized yards.

At the heart of the Cub Cadet 23HP is its reliable engine. The 23 horsepower engine provides ample power to tackle tough mowing conditions and hilly terrains effortlessly. The engine is designed for optimal performance, ensuring that the tractor operates smoothly under various conditions. With a reliable starter system, getting the tractor running is quick and efficient, allowing users to get to work without delay.

One of the standout features of the Cub Cadet 23HP is its innovative cutting deck. The 46-inch or 54-inch cutting deck options are designed for precision and efficiency, providing an excellent cut quality while reducing the time spent mowing. The deck is equipped with adjustable cutting heights, allowing users to customize their lawn care to match their specific needs. This adaptability ensures that the mower can handle different grass types and lengths with ease.

Comfort is another key characteristic of the Cub Cadet 23HP. The tractor features an adjustable high-back seat that provides support during long mowing sessions. Its ergonomic design ensures that users can maintain a natural posture while operating the tractor, reducing fatigue. The steering wheel is also designed for ease of use, allowing for smooth maneuverability even in tight spaces.

In terms of technology, the Cub Cadet 23HP comes equipped with advanced features that improve user experience. The LED headlights provide excellent visibility for early morning or late evening mowing. Additionally, the tractor features a dashboard with clear gauges that keep users informed about fuel levels, engine temperature, and other essential metrics.

Safety is a priority with the Cub Cadet 23HP. The tractor is equipped with safety features such as a seat switch that ensures the mower stops when the operator leaves the seat. This feature reduces the risk of accidents and enhances overall safety during operation.

Overall, the Cub Cadet 23HP lawn tractor combines power, comfort, and cutting-edge technology to deliver an exceptional mowing experience. Whether you have a small backyard or a larger property, this lawn tractor is designed to meet a variety of landscaping needs efficiently, making lawn care a hassle-free task. With its robust build and thoughtful features, the Cub Cadet 23HP is an investment in maintaining a beautiful lawn.