Cub Cadet 2176 manual Wheel Alignment, Front Wheel Adjustment, Pivot BAR Adjustment

Page 19

WHEEL ALIGNMENT

The front wheels should toe-in approximately 1/8 to 1/4 inch, as measured across dimensions A and B shown in Figure 12.

PERPENDICULAR

LOWER

TO FRAME

STEERING

 

ARM

Figure 12. Viewed from beneath the tractor.

FRONT WHEEL ADJUSTMENT

WARNING

Place the tractor on a firm and level surface.

To adjust the toe-in, proceed as follows:

1.Check the lower steering arm to ensure it is perpendicular to the tractor frame (See Figure 12).

2.Place a mark at the same spot on both front wheels; preferably the inner bead flange of the wheel rims.

3.Rotate the wheels to position the marks at the front horizontal diameter of the wheels, then measure the distance between the marks and the bottom edges of the tractor frame channels (See measurement D in Figure 12). These two measurements should be equal.

4.While holding the steering arms to prevent the steering knuckles from moving, rotate the marks to the rear horizontal diameter. Measure the distance between the marks and the frame (See measurement C in Figure 12). Measurement D should be approximately 1/16 to 1/8 inch less than measurement C on each side of the tractor.

5.Disconnect the front ball joints from the steering arms by removing the hex lock nuts (Refer to Figure 13). Manually move each wheel to achieve the required toe-in and equal D measurements.

6.Loosen the jam nuts from the ball joints (See Figure 13).

BALL JOINT

JAM NUT

TIE ROD

HEX

LOCK

NUT

STEERING

ARM

Figure 13

7.Making sure not to move the lower steering arm or either wheel, turn the ball joint in or out on each tie rod as necessary to align with the hole in each steering arm.

8.Reinstall the ball joints in the steering arms and secure with the hex lock nuts. Tighten the jam nuts against the ball joints.

PIVOT BAR ADJUSTMENT

CAUTION

The tractor should be checked every 50 hours of operation for play between the frame axle channel and the pivot axle.

Check and adjust the pivot axle as follows:

1.Raise the front ot the tractor and set it on jack stands, so the front wheels are suspended above the ground.

CAUTION

For safety, block the rear wheels to prevent the tractor from rolling and tipping or sliding the jack stands.

19

Image 19
Contents OPERATOR’S Manual Important Read Safety Rules and Instructions CarefullyMANUFACTURER’S Warranty Coverage Tractor and Deck Preparation ContentsGeneral Operation Safe Operation PracticesDo not II. Slope OperationIII. Children IV. Service Product Graphics Deflector and Safety GraphicSerial Number Location To the OwnerSafety Interlock Switches Not Shown Section I. Controls and IndicatorsHour Meter LOW OIL IndicatorPower TAKE-OFF PTO Control Switch IGNITION/LIGHT SwitchForward Control Pedal Lift Height IndicatorSeat Adjustment Lever Brake PedalFuel Tank Safety Interlock SwitchesHood and Side Panels Page Before Operating Your Tractor Section II. OperationStarting the Engine Stopping the Engine Tractor BREAK-IN ProcedureCold Weather Starting Driving the Tractor Drawbar Operating the Power TAKE-OFF PTO ClutchDriving on Slopes Stopping the TractorAdjusting the Seat Section III. AdjustmentsAdjusting the Brakes Pivot BAR Adjustment Front Wheel AdjustmentWheel Alignment Checking the Transmission Neutral Setting Hydrostatic Neutral AdjustmentPivot Sleeve Neutral Arm Adjusting Lift Assist Spring TensionFront Control Rod Rear Control Rod Hex Tap Screw ControlCarburetor Adjustments Checking the OIL Level Section IV. MaintenanceEngine Maintenance Engine OILDraining OIL and Replacing OIL Filter Adding OILFilling the Crankcase Adding Transmission OIL Checking Transmission OIL LevelHydrostatic Drive OIL Filter Servicing the Precleaner AIR CleanerServicing the Paper Element Air Cleaner Cover Paper Element Wing NutElement Cover Air Cleaner Base Rubber Grommet Cleaning EngineFuel Filter Spark PlugHeadlights Common Causes for Battery Failure General Battery InformationMaintenance of Battery Storage of the BatteryWash Hands after handling Battery Removal or InstallationBattery Removal Battery InstallationTire SizePounds per Square Inch TiresMounting Tires on the RIM Section V. Mower Deck SIDE-TO-SIDE Leveling AdjustmentFinger guard Blade Hard Level Surface Measure This Distance Front to Back Leveling AdjustmentGauge Wheel Adjustment Rear Gauge Wheel Cutting Height AdjustmentFlat WasherRemoval of Deck Removal and Installation of Deck AssemblyFront Lift ROD Roller Bracket Installation of Deck Front Roller Bracket Lift ROD Install the forward end of the PTO belt on the PTO Cleaning and Blade Care MaintenanceLubrication Spindle Drive Belt Replacement Installation of Mulching PlugSection VI. OFF-SEASON Storage Mowing Section VII. MowingMowing with Mulching Option Optional Equipment and Accessories Month Season Yearly Storage Maintenance ChartEngine Operates Irregularly or Knocks Hard to StartPTO Clutch will not Engage Nance Trouble ShootingLack of Power MaintenanceLubrication Table Lubrication Guide Lubrication Guide Guide Engine SpecificationsPage Slope Gauge Commercial USE Residential USE CUB Cadet Corporation MANUFACTURER’S Limited WarrantyMaintenance Parts Chart

2176 specifications

The Cub Cadet 2176 lawn tractor is a powerhouse in the realm of residential lawn care, designed to provide users with enduring performance and exceptional features. Known for its reliability and user-friendly operation, this model combines power, comfort, and innovative technology, making it a preferred choice among homeowners.

At the heart of the Cub Cadet 2176 is its robust 17-horsepower Kohler engine. This engine not only ensures ample power for mowing but also handles larger lawns with ease. The hydrostatic transmission allows for smooth operation, offering easy speed adjustments without the need for shifting gears. This feature is particularly beneficial for those who need to navigate around obstacles or work in tighter spaces.

One of the standout characteristics of the Cub Cadet 2176 is its 42-inch cutting deck. This wide cutting path allows users to cover more ground in a shorter amount of time, making lawn maintenance more efficient. The deck is equipped with a washout port, enabling easy cleaning after use, which prolongs its lifespan and ensures optimal performance.

Comfort is a key consideration in the design of the 2176. The lawn tractor features a comfortable, adjustable seat that allows for prolonged use without discomfort. Additionally, the operator's presence control (OPC) ensures that the tractor stops when the operator leaves the seat, improving safety during operation.

Moreover, the Cub Cadet 2176 incorporates the company’s signature Cadet Smart technology, providing users with enhanced diagnostics and maintenance reminders. This technology enables users to monitor the tractor’s performance and receive alerts for maintenance tasks, ensuring that the machine runs efficiently year-round.

Another notable feature is the ease of use. The controls are strategically placed for simple access, allowing for intuitive operation. The tractor also supports a variety of attachments, including baggers, mulchers, and snow plows, making it a versatile choice for year-round functionality.

In conclusion, the Cub Cadet 2176 lawn tractor stands out for its blend of power, comfort, and advanced technology. With its powerful engine, efficient cutting deck, user-friendly controls, and innovative features, it is a reliable companion for maintaining a beautiful lawn. Whether dealing with weekly mowing duties or seasonal tasks, the Cub Cadet 2176 meets the demands of modern homeowners seamlessly.