Cub Cadet 2206 manual Adding OIL, Draining OIL and Replacing OIL Filter

Page 24

ADDING OIL

CAUTION

Never overfill the engine crankcase. The engine may overheat and/or damage may result if the crankcase is below the “LOW” mark or over the “FULL” mark on the dipstick.

NOTE

For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Always check the level on the dipstick before adding more oil.

Refer to the LUBRICATION TABLE for information regarding the proper type of oil to add to the crankcase.

1.Place the tractor on a level surface and engage the brake pedal lock. Stop the tractor engine and remove the ignition key.

2.Clean the area around the oil level dipstick, dipstick tube, and the oil filler cap to prevent debris from entering the crankcase.

3.Remove the oil filler cap from the left valve cover and SLOWLY pour in oil. Fill the crankcase until the oil level reaches the “FULL” mark on the dipstick (Refer to Figure 18).

4.Reinstall the oil filler cap by screwing it securely into the valve cover.

CAUTION

The oil filler cap MUST BE TIGHTENED SECURELY INTO THE VALVE COVER AT ALL TIMES WHEN THE ENGINE IS OPERATING. Severe engine damage could result from failure to do so.

DRAINING OIL AND REPLACING OIL FILTER

NOTE

The engine oil should be changed after the first 5 hours of operation. Then oil should be changed after every 100 hours of operation.

WARNING

If the tractor has recently been operated, the engine and surrounding areas may be hot. Use caution not to burn yourself when removing the side panels, draining the oil from the crankcase, and changing the oil filter.

NOTE

The oil filter should be changed at every oil change interval. The filters can be obtained through your Cub Cadet dealer under part number KH-12-050-08.

Refer to the MAINTENANCE CHART and the LUBRICATION TABLE for information regarding the frequency of required oil changes and the quantity and type of oil needed.

The oil filter is located behind the left side panel and is mounted on the engine (See Figure 19).

OIL

FILTER

PLASTIC

CAP

FLEXIBLE

TUBING

OIL DRAIN

VALVE

Figure 19

Run the engine for a few minutes to allow the oil in the crankcase to warm up. Warm oil will flow more freely and carry away more of the engine sediment which may have settled at the bottom of the crankcase. Use care to avoid burns from hot oil.

24

Image 24
Contents Important Read Safety Rules and Instructions Carefully OPERATOR’S ManualMANUFACTURER’S Warranty Coverage Contents Tractor and Deck PreparationSafe Operation Practices General OperationII. Slope Operation Do notIII. Children IV. Service Safety Graphic Located on Left Side of Mower Deck Deflector and Safety GraphicProduct Graphics To the Owner Serial Number LocationSection I. Controls and Indicators Safety Interlock Switches Not ShownLOW OIL Indicator Power TAKE-OFF PTO Control SwitchIGNITION/LIGHT Switch Hour MeterLift Height Indicator Seat Adjustment LeverBrake Pedal Forward Control PedalSafety Interlock Switches Fuel TankHood and Side Panels Page Section II. Operation Before Operating Your TractorStarting the Engine Tractor BREAK-IN Procedure Stopping the EngineCold Weather Starting Driving the Tractor Operating the Power TAKE-OFF PTO Clutch Driving on SlopesStopping the Tractor DrawbarSection III. Adjustments Adjusting the SeatAdjusting the Brakes Front Wheel Adjustment Pivot BAR AdjustmentWheel Alignment Hydrostatic Neutral Adjustment Checking the Transmission Neutral SettingAdjusting Lift Assist Spring Tension Front Control Rod Rear Control Rod Hex Tap ScrewControl Pivot Sleeve Neutral ArmCarburetor Adjustments Section IV. Maintenance Engine MaintenanceEngine OIL Checking the OIL LevelAdding OIL Draining OIL and Replacing OIL FilterFilling the Crankcase Checking Transmission OIL Level Adding Transmission OILHydrostatic Drive OIL Filter AIR Cleaner Servicing the PrecleanerAir Cleaner Cover Paper Element Wing Nut Element Cover Air Cleaner Base Rubber GrommetCleaning Engine Servicing the Paper ElementSpark Plug Fuel FilterHeadlights General Battery Information Maintenance of BatteryStorage of the Battery Common Causes for Battery FailureBattery Removal or Installation Battery RemovalBattery Installation Wash Hands after handlingTires Tire SizePounds per Square InchMounting Tires on the RIM Installation of Deck Section V. Mower DeckQuick Attach ROD Captured Lift ROD Bracket Assembly Idler ARM Lever Stop Bracket PTO Belt Mower Deck Center Double Pulley Front of Deck Removal of Deck Idler ARM Lever Stop Bracket Front Lift ROD Front Roller Bracket Slots Side to Side Leveling Adjustment AdjustmentFinger guard Blade Hard Level Surface Measure This Distance Front to Back Leveling Adjustment Cutting Height Adjustment Cleaning and Blade Care LubricationSpindle Drive Belt Replacement Movable Idler Pulley Idler Arm Lever Spindle Drive BeltSection VI. OFF-SEASON Storage Section VII. Mowing MowingOptional Equipment and Accessories Maintenance Chart Month Season Yearly StorageHard to Start Engine Operates Irregularly or KnocksPTO Clutch will not Engage Trouble Shooting Lack of PowerMaintenance NanceLubrication Table Lubrication Guide Lubrication Guide 100 Specifications EnginePage Slope Gauge Commercial USE CUB Cadet Corporation MANUFACTURER’S Limited Warranty Residential USEMaintenance Parts Chart

2206 specifications

The Cub Cadet 2206 is a versatile and robust lawn tractor designed for residential lawn care enthusiasts. It represents the perfect blend of power, precision, and convenience, making it an essential tool for maintaining a pristine landscape.

At the heart of the Cub Cadet 2206 is a reliable Kohler 20 HP engine. This powerful engine provides ample torque and acceleration, enabling users to tackle even the toughest mowing tasks with ease. The engine is built with durability in mind, ensuring long-lasting performance and reduced maintenance concerns.

One of the standout features of this lawn tractor is its 46-inch cutting deck, which allows users to cover large areas quickly while achieving a clean, manicured look. The cutting height is adjustable, providing the flexibility to customize grass length according to personal preferences or lawn care requirements. The deck is designed with a robust structure, ensuring it can withstand regular use while providing consistent results.

The Cub Cadet 2206 employs the innovative Automatic Transmission system that allows for smooth and effortless operation. This user-friendly system provides forward and reverse speeds without the need for manual shifting, making it ideal for navigating around obstacles and maneuvering in tight spaces. The ergonomic steering wheel and comfortable seat enhance the overall driving experience, reducing fatigue during extended mowing sessions.

When it comes to versatility, the Cub Cadet 2206 excels with its optional attachments. Gardeners can equip the tractor with various accessories such as baggers for grass clippings, snow blades for winter snow removal, and spreaders for fertilizing, making it an all-season asset. This adaptability ensures that homeowners can rely on their Cub Cadet throughout the year.

The machine also features a sturdy frame and high-traction tires, ensuring stability and grip on various terrains. This reliability is critical for maintaining control and safety while operating the tractor on sloped or uneven ground.

Additionally, the Cub Cadet 2206 is designed with user-friendly maintenance features. The easy-access oil filter and spacious engine compartment make routine upkeep significantly more manageable, contributing to the tractor's longevity and performance.

In summary, the Cub Cadet 2206 is an exceptional lawn tractor that combines power, comfort, and versatility. Whether you're mowing a small yard or a larger landscape, this machine's advanced features and user-centric design make lawn care a straightforward and enjoyable task. With proper maintenance and care, the Cub Cadet 2206 can be a reliable partner in keeping your outdoor space looking its best for years to come.