Cub Cadet 2206 Battery Removal or Installation, Wash Hands after handling, Battery Installation

Page 31

BATTERY REMOVAL OR INSTALLATION

WARNING

Battery posts, terminals and related accessories contain lead and lead compounds.

Wash Hands after handling.

When removing the battery, disconnect the battery cables in the following order to avoid arcing and the resulting sparks:

Battery Removal:

1.Disconnect the Negative cable.

2.Disconnect the Positive cable.

Battery Installation:

1.Connect the Positive cable.

2.Connect the Negative cable.

To replace the battery, proceed as follows:

1.Remove the negative cable from the negative terminal of the battery, then remove the positive cable from the positive terminal.

2.Remove the wing nut securing the mounting rod to the bulkhead mounting bracket (Refer to Figure 26) and pull the rod downward from the bulkhead bracket.

WING NUT

MOUNTING ROD

Figure 26

3.Rotate the mounting rod fully upward toward the dash panel to provide clearance for battery removal (See Figure 27).

4.Pull downward on the bottom of the battery holddown strap to release it from the tab beneath the battery tray.

5.Lift the battery upward and remove from the left side of the tractor.

HOLDDOWN

STRAP

MOUNTING

ROD

ROTATE

UPWARD

Figure 27

6.Install the new battery from the left side of the tractor and lower into the battery tray.

7.Stretch the battery holddown strap downward across the front of the battery and hook to the tab below the battery tray.

8.Rotate the mounting rod downward and insert through the bottom of the hole in the bulkhead mounting bracket (See Figure 26).

9.Install the wing nut onto the mounting rod, but do not tighten until after the side panels are installed.

10.Connect the positive cable to the positive terminal of the battery, then connect the negative cable to the negative terminal.

JUMP STARTING

WARNING

Failure to use this jump starting procedure could cause sparking, which could result in an explosion of either battery.

1.Attach the first jumper cable from the positive terminal of the good battery to the positive terminal of the dead battery.

2.Attach the second jumper cable from the negative terminal of the good battery to the FRAME OF THE UNIT WITH THE DEAD BATTERY.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents OPERATOR’S Manual Important Read Safety Rules and Instructions CarefullyMANUFACTURER’S Warranty Coverage Tractor and Deck Preparation ContentsGeneral Operation Safe Operation PracticesDo not II. Slope OperationIII. Children IV. Service Deflector and Safety Graphic Safety Graphic Located on Left Side of Mower DeckProduct Graphics Serial Number Location To the OwnerSafety Interlock Switches Not Shown Section I. Controls and IndicatorsHour Meter LOW OIL IndicatorPower TAKE-OFF PTO Control Switch IGNITION/LIGHT SwitchForward Control Pedal Lift Height IndicatorSeat Adjustment Lever Brake PedalFuel Tank Safety Interlock SwitchesHood and Side Panels Page Before Operating Your Tractor Section II. OperationStarting the Engine Stopping the Engine Tractor BREAK-IN ProcedureCold Weather Starting Driving the Tractor Drawbar Operating the Power TAKE-OFF PTO ClutchDriving on Slopes Stopping the TractorAdjusting the Seat Section III. AdjustmentsAdjusting the Brakes Pivot BAR Adjustment Front Wheel AdjustmentWheel Alignment Checking the Transmission Neutral Setting Hydrostatic Neutral AdjustmentPivot Sleeve Neutral Arm Adjusting Lift Assist Spring TensionFront Control Rod Rear Control Rod Hex Tap Screw ControlCarburetor Adjustments Checking the OIL Level Section IV. MaintenanceEngine Maintenance Engine OILDraining OIL and Replacing OIL Filter Adding OILFilling the Crankcase Adding Transmission OIL Checking Transmission OIL LevelHydrostatic Drive OIL Filter Servicing the Precleaner AIR CleanerServicing the Paper Element Air Cleaner Cover Paper Element Wing NutElement Cover Air Cleaner Base Rubber Grommet Cleaning EngineFuel Filter Spark PlugHeadlights Common Causes for Battery Failure General Battery InformationMaintenance of Battery Storage of the BatteryWash Hands after handling Battery Removal or InstallationBattery Removal Battery InstallationTire SizePounds per Square Inch TiresMounting Tires on the RIM Section V. Mower Deck Installation of DeckQuick Attach ROD Captured Lift ROD Bracket Assembly Idler ARM Lever Stop Bracket PTO Belt Mower Deck Center Double Pulley Front of Deck Removal of Deck Idler ARM Lever Stop Bracket Front Lift ROD Front Roller Bracket Slots Adjustment Side to Side Leveling AdjustmentFinger guard Blade Hard Level Surface Measure This Distance Front to Back Leveling Adjustment Cutting Height Adjustment Lubrication Cleaning and Blade CareMovable Idler Pulley Idler Arm Lever Spindle Drive Belt Spindle Drive Belt ReplacementSection VI. OFF-SEASON Storage Mowing Section VII. MowingOptional Equipment and Accessories Month Season Yearly Storage Maintenance ChartEngine Operates Irregularly or Knocks Hard to StartPTO Clutch will not Engage Nance Trouble ShootingLack of Power MaintenanceLubrication Table Lubrication Guide Lubrication Guide 100 Engine SpecificationsPage Slope Gauge Commercial USE Residential USE CUB Cadet Corporation MANUFACTURER’S Limited WarrantyMaintenance Parts Chart

2206 specifications

The Cub Cadet 2206 is a versatile and robust lawn tractor designed for residential lawn care enthusiasts. It represents the perfect blend of power, precision, and convenience, making it an essential tool for maintaining a pristine landscape.

At the heart of the Cub Cadet 2206 is a reliable Kohler 20 HP engine. This powerful engine provides ample torque and acceleration, enabling users to tackle even the toughest mowing tasks with ease. The engine is built with durability in mind, ensuring long-lasting performance and reduced maintenance concerns.

One of the standout features of this lawn tractor is its 46-inch cutting deck, which allows users to cover large areas quickly while achieving a clean, manicured look. The cutting height is adjustable, providing the flexibility to customize grass length according to personal preferences or lawn care requirements. The deck is designed with a robust structure, ensuring it can withstand regular use while providing consistent results.

The Cub Cadet 2206 employs the innovative Automatic Transmission system that allows for smooth and effortless operation. This user-friendly system provides forward and reverse speeds without the need for manual shifting, making it ideal for navigating around obstacles and maneuvering in tight spaces. The ergonomic steering wheel and comfortable seat enhance the overall driving experience, reducing fatigue during extended mowing sessions.

When it comes to versatility, the Cub Cadet 2206 excels with its optional attachments. Gardeners can equip the tractor with various accessories such as baggers for grass clippings, snow blades for winter snow removal, and spreaders for fertilizing, making it an all-season asset. This adaptability ensures that homeowners can rely on their Cub Cadet throughout the year.

The machine also features a sturdy frame and high-traction tires, ensuring stability and grip on various terrains. This reliability is critical for maintaining control and safety while operating the tractor on sloped or uneven ground.

Additionally, the Cub Cadet 2206 is designed with user-friendly maintenance features. The easy-access oil filter and spacious engine compartment make routine upkeep significantly more manageable, contributing to the tractor's longevity and performance.

In summary, the Cub Cadet 2206 is an exceptional lawn tractor that combines power, comfort, and versatility. Whether you're mowing a small yard or a larger landscape, this machine's advanced features and user-centric design make lawn care a straightforward and enjoyable task. With proper maintenance and care, the Cub Cadet 2206 can be a reliable partner in keeping your outdoor space looking its best for years to come.
Top Page Image Contents