Cub Cadet 108, 86, 128, 129, 169, 149 Fastened, Engine Cooling, DRY Type AIR Cleaner, Ignition Switch

Page 23

ENGINE COOLING

This tractor has an air cooled engine. Air must be able to circulate freely around the engine, through the screen, shroud, and over the fins of the cylinder head and cylinder block. Keep these areas free of accumulated dirt and trash or engine will overheat and result in damaged moving parts. Periodic cleaning with compressed air will keep area clear for adequate cooling.

DRY TYPE AIR CLEANER

Removing the air cleaner filter element.

The twelve-volt electrical system consists princi- pally of a motor-generator, voltage regulator, and a twelve-volt battery.

All connections must be clean and securely

fastened.

IGNITION SWITCH

Turn the key clockwise to turn on the ignition. A further turn actuates the motor-generator. The key cannot be removed when in the "ON" position.

Incoming air for combustion is filtered by a dry-type air cleaner having a filter element inside of the cover.

Clean or replace the element when loss of power is noticeable. Replace at least once a year.

Cleaning the Element -To clean the element, remove wing nut, air cleaner cover, then remove element and tap it lightly on a flat surface to cause loose dirt to falloff. Handle paper element with care to avoid dents or crushing local areas. Do not use compressed air to remove dirt as this can repture the element. Do not wash or use a solvent.

Replacing the Element -Replace element with a new one if dirt does not drop off easily, or if it is bent or damaged. When replacing element be sure the back plate is securely tightened to the carbu- retor. Replace the back plate if bent or cracked, then be sure the element fits snugly around the inside edge of the air cleaner base. The gasket surfaces of the element must be flat against the back plate and cover to seal effectively. Replace cover and tighten wing nut finger tight.

NOTE: When the engine is not operating, the key must be turned to the "OFF" position to prevent battery discharge.

SAFETY STARTING SWITCH

The safety starting switches activated by the clutch-brake pedal and the power take-off clutch lever serve to prevent starting the engine acci- dentally.

21

Image 23
Contents Page Cumstancesshouldyou Attemptto Service These UnitsPage Page Page Model Delivery Date Serial No and aboveRead the Operators Manual Seepage Seepage 18 Seepage22 Seepage Seepage18 Seepage22 Seepage20 Seepage21 Governor LubricationThrottle Lever Stopping the Engine Operatingthe Engine Lifting the HoodStarting the Engine Fuel SHUT-OFF Valve Carburetor AdjustmentsFuel System Adjusting the High-SpeedAdjustment Screw Locking the Brake Adjusting the seatClutch and Brake Pedal Starting the Tractor Speedsand one reverse speed. Refer toCLUTCH-BRAKE Pedal Gearshift Lever Stopping the TractorDepth Rearward providesthe reversespeedsRelease Lever Height AdjustmentDriving the Tractor Starting TractorUse Cam lock knobCamstop TangShifter lever Power take-off guard Greasefitting Advancethrottle to operating speed ClutchElectriclift Operating Instructions Tion before making any adjustments to the machineLocking knob2. Cam stop3. Rockshaft arm Operating Instructions Fastened DRY Type AIR CleanerIgnition Switch Safety Starting SwitchRepairs.22 Lights SaryElectrical System Voltage RegulatorRear Tires ConnectingBoosterBatteriesNeeded LevelOverloading Rear Wheel Weights InflationPneumatic Tires Care of Tires Mounting Tires on the RIM Front Wheel TOE-IN Front quick attaching latchWheelhub Front Quick Attaching LatchBrakes Adjusting the ClutchAdjusting CLUTCH-BRAKE Reconnect the left brake rod. Turn the left Brake adjustmentsAdjusting the Brakes Removing from Storage Plate DisengageP.T.G. clutchMachine outside the storage room before GasHard to Start PossibleRemedyPlug 129, 149, Seeyour International Harvesterdealer OtherengineproblemsCheck the breaker points and breaker point open Engine OIL TureCase EngineCrankcase Models 108 129, 149, Tractors Point of LubricationAt at Capacity Above+32FLubrication Guide Lubricationguioe Lubricationguide ~£~~ Transmission Steeringknuckes2.3 Front axle pivot pinLubrication Guide Powertake-off shaft governed Speed 515r.p.mSpeed control rod Cam plates Page Amp SystemvoltageUnit AGC-10Page Quick-attachable mounting MowersPage Page 2Do43 Not carry passengersor giveridesPage ~D Operating Side to Side Adjustingand OperatingBEL T Operating BEL T General Adjustingand Dperating Height of CUTCleaning LubricationPage Page Page Page Page Page Page Page Page Page BeAccidents
Related manuals
Manual 69 pages 21.49 Kb