Cub Cadet 129, 86, 128 Plate DisengageP.T.G. clutch, Machine outside the storage room before, Gas

Page 32

When your tractor is not to be used for some time, it should be stored in a dry and protected place. Leaving your tractor out-doors, exposed to the elements materially shortens its life.

Follow the procedure outlines below when storing a tractor for an extended period of time.

1.Wash or clean and completely lubricate the tractor. See the "lubrication Guide".

2.Store the tractor so the tires are p':.Jtectedfrom light. Before storing the tractor, clean the tires thoroughly. Jack up the tractor so the load is off the tires when it is to be out of service for a long period. If not jacked up, inflate the tires at regular intervals.

CAUTION! If tractor is jacked up or placed on blocks, be sure it is done so it cannot be tipped over or fall on

someone.

6.Cleanthe exterior of the engine.

7.Removethe battery and place it in a cool, dry place above (+32°F.). Check battery at leastonce a month for water level and amount of charge. See pages24 and 25.

On all gear driven International Cub Cadet Tractors press clutch and brake pedal all the way down and engage the brake pedal lock. This will prevent clutch lining from sticking to pressure

plate.

DisengageP.T.G. clutch.

REMOVING FROM STORAGE

1.Fill the fuel tank and be sure the grade of oil in the crankcase is according to the temperature range in the "lubrication Table".

3.Run the engine long enough to thoroughly warm the oil in the crankcase and then drain the oil. Refill the crankcase with fresh oil as specified in the "lubrication Table" and run the engine for about five minutes.

2.Install a fully charged battery and properly connect.

3.Start the engine and let it run slowly. Do not accelerate it rapidly or operate at high speed immediately after starting.

Drain the fuel tank and run the engine until the fuel is exhausted from the fuel system.

NOTE: Gum will eventually form in the fuel tank, line, and carburetor if the unit is not drained.

5.After the engine has cooled, remove the spark plug and pour two tablespoonsful of a rust inhibited oil such as Hy-Tran@ or IH No. 1@ engine oil into the cylinder. Crank engine slowly turning generator belt by hand to distribute the oil over the cylinder walls. Then replace spark plug.

30

ACAUTION J Keep doors wide open or re- lease brake pedal lock and move the

machine outside the storage room before

engine is started to avoid the danger from exhaust

gas.

Check air pressure in tires.

98.4

Image 32
Contents Page Service These Units Cumstancesshouldyou AttempttoPage Page Page Serial No and above Model Delivery DateRead the Operators Manual Seepage Seepage 18 Seepage22 Seepage Seepage18 Seepage22 Seepage20 Seepage21 Governor LubricationThrottle Lever Stopping the Engine Operatingthe Engine Lifting the HoodStarting the Engine Fuel SHUT-OFF Valve Carburetor AdjustmentsFuel System Adjusting the High-SpeedAdjustment Screw Locking the Brake Adjusting the seatClutch and Brake Pedal Speedsand one reverse speed. Refer to CLUTCH-BRAKE PedalGearshift Lever Stopping the Tractor Starting the TractorRearward providesthe reversespeeds DepthHeight Adjustment Driving the TractorStarting Tractor Release LeverCam lock knob CamstopTang UseShifter lever Power take-off guard Greasefitting Clutch Advancethrottle to operating speedElectriclift Operating Instructions Tion before making any adjustments to the machineLocking knob2. Cam stop3. Rockshaft arm Operating Instructions DRY Type AIR Cleaner Ignition SwitchSafety Starting Switch FastenedRepairs.22 Sary Electrical SystemVoltage Regulator LightsConnectingBoosterBatteries NeededLevel Rear TiresOverloading Rear Wheel Weights InflationPneumatic Tires Care of Tires Mounting Tires on the RIM Front quick attaching latch WheelhubFront Quick Attaching Latch Front Wheel TOE-INBrakes Adjusting the ClutchAdjusting CLUTCH-BRAKE Reconnect the left brake rod. Turn the left Brake adjustmentsAdjusting the Brakes Plate DisengageP.T.G. clutch Machine outside the storage room beforeGas Removing from StorageHard to Start PossibleRemedyPlug 129, 149, Seeyour International Harvesterdealer OtherengineproblemsCheck the breaker points and breaker point open Ture Engine OILCase Point of Lubrication At at CapacityAbove+32F EngineCrankcase Models 108 129, 149, TractorsLubrication Guide Lubricationguioe Lubricationguide ~£~~ Steeringknuckes2.3 Front axle pivot pin TransmissionLubrication Guide Powertake-off shaft governed Speed 515r.p.mSpeed control rod Cam plates Page Systemvoltage UnitAGC-10 AmpPage Mowers Quick-attachable mountingPage Page Not carry passengersor giverides 2Do43Page ~D Operating Adjustingand Operating Side to SideBEL T Operating BEL T Adjustingand Dperating Height of CUT CleaningLubrication GeneralPage Page Page Page Page Page Page Page Page Page BeAccidents
Related manuals
Manual 69 pages 21.49 Kb

108, 149, 169, 129, 128 specifications

The Cub Cadet series of tractors, particularly models 129, 86, 169, 149, and 128, represents a significant chapter in the history of garden and lawn care machinery. Known for their durability and innovative features, these tractors offer a blend of power and functionality that appeals to both homeowners and agricultural enthusiasts.

One of the main attractions of these models is their robust construction. Built with a heavy-duty frame, they are designed to withstand the rigors of outdoor tasks such as mowing, tilling, and hauling. The engines are typically Kohler or Tecumseh, providing reliable performance and ample power for various attachments. This capability allows these tractors to excel in tasks, from simple grass cutting to challenging snow removal.

The Cub Cadet 129, for example, offers a 12-horsepower engine, making it suitable for many residential landscaping needs. Its hydrostatic transmission provides smooth operation, allowing for easy speed adjustments without having to shift gears manually, making it user-friendly. Likewise, the 149 model features a similar engine, with the added benefit of a wider cutting deck, improving efficiency for larger lawns.

The Cub Cadet 86 stands out with its unique design and powerful 8 horsepower engine. It also features easy access controls, allowing operators to efficiently switch between various attachments, enhancing overall productivity. This fluidity is mirrored in the 169 model, which integrates advanced steering mechanisms that provide greater maneuverability, allowing users to navigate tight spaces with ease.

Model 128 offers a blend of modern technology and classic charm. It is equipped with a comfortable seat for extended usage and ergonomic controls, responding to the needs of users who spend considerable time on their tractors. The combination of comfort and performance makes these tractors popular among gardening aficionados.

Overall, the Cub Cadet series boasts a legacy of reliability, with a focus on ergonomic design and user-friendly technology. Whether for professional landscaping or personal gardening, these models, with their powerful engines and robust capabilities, continue to be a preferred choice for those looking to enhance their outdoor experience.