Electrohome RV-3798 manual Programming the Remote to Control VCR

Page 30

PROGRAMMING THE REMOTE

PROGRAMMING THE REMOTE TO CONTROL

A VCR

To determine whether you need to program the remote, turn on the VCR, point the remote at the VCR’s remote sensor, and press VCR. Then, press the POWER or CH + or CH – button to see if the VCR responds to the remote commands. If not, you need to program the remote.

Follow these steps to program your remote to control your VCR:

1.Turn on the VCR.

2.Look up your VCR brand and code number(s) in the code list on the next page or on the code sheet packed with your remote.

3.Press and hold the VCR1 button on the remote.

4.Enter the three-digit code from the code list.

5.Release the VCR button, then press POWER to see if the VCR responds to the remote commands. If not, try pressing VCR

then POWER.

6.Repeat steps 3 through 5 using the next code listed for your VCR brand until the VCR responds to the remote commands.

This remote may not operate all models of the brands shown.

To program the LD•VCR2 button to control a second VCR, follow these steps but use the LD•VCR2 button instead of the VCR button.

28

Image 30

Contents USER’S Guide Safety Information Table of Contents Table of Contents First Things First First Things FirstUnpack the Receiver Connect the ReceiverTV only PUT Batteries in the Remote Plug in the ReceiverTurn on the Receiver Page Operating the Receiver Operating the ReceiverAuto Tuning Tuning the Receiver Using RemoteTuning Storing Stations in MemoryPreset Scanning To Play a Preset StationBalancing the Speaker System To Balance the SpeakersUsing Swap Audio To USE Swap AudioTo Change the Video Source and Swap the Audio Page Tour of the Receiver Buttons and Connections3TOUR of the Receiver Front Panel 160W, 5 ChannelTour of the Receiver Status Indicators Front Panel DisplaysMode Displays Surround MemoryFunction Displays Remote Control Basic ControlsReceiver Controls Surround Sound Level Controls RECEIVER/TUNER ControlsTV Controls VCR Controls DVD Player Controls Satellite Receiver ControlsCD Player Controls Tape Deck ControlsLaserdisc Player Controls Back Panel AudioProgramming the Remote 4PROGRAMMING the RemoteProgramming the Remote Programming the Remote to Control a TVRemote TV Codes AOCProgramming the Remote to Control VCR Remote VCR Codes Programming the Remote to Control AN Audio Component Audio CodesThis remote may not operate all models of the brands shown Remote Controllable Cable BOX Codes Programming the Remote to Control a Cable BOXProgramming the Remote to Control a DVD Player Programming the Remote to Control a Laserdisc PlayerLaserdisc Player Codes Receiver Remote works like DVD RemoteSatellite Receiver Codes Programming the Remote to Control AN RCA Brand DSS ReceiverProgramming the Remote to Control a Satellite Receiver Receiver Remote works like RCA DSS RemotePage Appendix a Connecting the Receiver Things to Know Before Connecting the ComponentsProtect Your Components From Overheating Using the Switched OutletUsing the Subwoofer Connections AC OutletsThis Connection Provides Using this ConnectionTV and VCR To USE this CONNECTION, YOU should haveTo watch TV programs in stereo RCA DSS ReceiverTo USE this CONNECTION, YOU Must have To watch satellite programmingDVD Player Diagram BPress DVD to put the receiver in DVD mode Press play To play a DVDSecond VCR To play a tape on the second VCRCamcorder or Video Camera To play the camcorderLaserdisc Player To play the laserdiscCompact Disc Player To play a CDTo record a tape Tape Deck or Minidisc PlayerTo play a tape To play a minidiscTo listen to the radio FM Wire AntennaAntennas AM Loop AntennaSpeakers Appendix B Speaker Placement Speaker PlacementExample Remote Control Operation Appendix C TroubleshootingTroubleshooting Guide RECEIVER/TUNER OperationAppendix D Care and Cleaning Care and CleaningAppendix E FCC Information FCC InformationAppendix F Limited Warranty Limited WarrantyAppendix G Equipment Specifications Equipment SpecificationsAppendix G Equipment Specifications Appendix H Preset Station List Form Preset Number Band FrequencySymbols IndexPIP VCR Tocom