Cub Cadet GT 3200 warranty Electrical Box, Fuse, Front Wheel Alignment, Adjusting the Brake

Page 28

Electrical Box

The electrical box contains the relay and fuses. Refer to Figure 19 for the electrical box layout. The electrical box is located under the upper air baffle in front of the dash panel. To access the electrical box:

•Raise the hood of the tractor

•Locate the locking tabs on the left and right side of the upper air baffle.

•Pull up on the locking tabs on each side of the upper air baffle, and remove the upper air baffle from the lower air baffle. Lift the upper air baffle from the tractor.

•Lift the locking tab and remove the cover from the electrical box.

5Amp Fuses

25Amp

FusesRelay

Figure 19

Fuse

Fuses are installed to protect the trac- tor’s electrical system from damage caused by excessive amperage.

Always use the same capacity fuse for replacement. Refer to the Specifica- tions Chart. If the electrical system does not function, check the fuses.

To replace a fuse, note the position of the fuse and pull the old fuse from the electrical box.

Compare the suspect fuse with Figure 20 to determine if is good or bad.

GOOD BAD

Figure 20

Install the new fuse in the position from which the old fuse was removed.

Front Wheel Alignment

Note: The left-hand ball joint is left- hand threaded.

The front wheels should toe-in approx- imately 1/8 inch. Measure distances A and B. A should be approximately 1/8 inch less than B. See Figure 21.

B

Front

A

Figure 21

To adjust toe-in, loosen left and right ball joint jam nuts. Refer to Figure 22. Turn the tie rod in or out of the ball joints as required to attain proper adjustment. Tighten the jam nuts against the ball joints.

Steering Axle

Hex Lock Nut

Tie Rod

Hex Jam Nut

Ball Joint

Figure 22

Adjusting the Brake.

Remove the rear drawbar from the frame by removing the four hex tapp screws. NOTE: The oil fill tube/dipstick will be pulled from the transmission housing. Plug or cover the hole in the transmission to prevent dirt or debris from entering.

From beneath the right/rear side of the tractor frame, secure the hex shaped flange of the brake rod (located just behind the brake link) to prevent the rod from turning (Refer to Figure 23).

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents OPERATOR’S Manual Series 3000 Tractor Model GTTable of Contents To the OwnerImportant Safe Operation Practices When you see this symbol. Heed ITS WarningGeneral Operation Never carry passengers Slope OperationDo Not Do not use a grass catcher on steep slopesChildren Be alert and turn machine off if a child enters the areaService General ServiceTowing Safe Handling of GasolineNever tamper with factory setting of engine governor Do Not Modify EngineSpark Arrestor Average Useful LifeSlope Guide Sight and hold this level with a vertical treeTractor Preparation Deck Front Lift Rod AssemblyPosition the High Back Seat Controls and Features Low Fuel Indicator Lamp Indicator Panel/Hour MeterSteering Wheel LCD Hour Meter DisplayIndicator Light Key Switch ModuleButton PTO Switch 12V Power OutletSeat Adjustment Lever Parking Brake Lever Forward PedalLower Raise Safety Interlock Switches OperationChoke Lever Starting The EngineStopping The Engine Setting The Cruise ControlDriving The Tractor Using the Hydraulic Lift System Driving On SlopesStopping The Tractor Auxiliary HydraulicsUsing the Reverse Caution Mode key position Reverse Caution ModeEngaging Differential Lock Using The DrawbarMowing Adjustments and Maintenance Checking Transmission Oil Level Operating Transmission Range Oil Fill Tube DipstickBattery Storage Battery MaintenanceTire Inflation Maintenance Chart Operation toBe performed Grease front wheel bearingsLubrication Illustration Service General Battery InformationBattery Removal Charging the BatteryHeadlight Bulb Replacement Adding Transmission Oil Dipstick must be installedAll times when the engine is Securely into the fill tube atChanging Transmission Oil Adjusting the Brake Electrical BoxFuse Front Wheel AlignmentHex Shaped Flange Hex Nylon Lock Nut AssemblyChanging the Engine Oil and Filter If using a fuel stabilizer Off-Season StorageMANUFACTURER’S Warranty Coverage OWNER’S Warranty ResponsibilitiesEngine Information CoverageMaintenance and Repairs Requirements LimitationsChecking Engine Oil Level Cleaning The EngineAdding Engine Oil Changing Engine Oil Sparkplugs Changing Air CleanerChanging Fuel Filter Servicing The Paper Element Servicing The PrecleanerServicing Oil Cooler Trouble Shooting Lack of PowerHard To Start Engine Operates Irregularly or KnocksOptional Equipment Description Model NumberSpecifications TiresBrakes Oil Filter Cartridge Crank Case CapacityReplacement Parts PRE-CLEANERDescription Part Number CartridgeGeneral Emissions Warranty Coverage Warranted Parts GDOC-100092 REV. a U.S.A Canada Transportation charges and service callsMTD Products Limited, Kitchener, on N2G 4J1, Phone
Related manuals
Manual 48 pages 30.97 Kb

GT 3200 specifications

The Cub Cadet GT 3200 is a powerful garden tractor that combines robust performance with innovative technology, making it ideal for homeowners and landscapers alike. This formidable machine is equipped with a heavy-duty Kohler engine, offering a variety of horsepower options to meet diverse needs. Whether used for mowing large lawns or tackling tough garden tasks, the GT 3200 proves to be a reliable workhorse.

One of the highlights of the GT 3200 is its Hydrostatic transmission, which provides seamless speed control without the need for manual gear shifting. This feature allows operators to easily navigate varying terrains, ensuring smooth operation in both forward and reverse. The precision steering system enhances maneuverability, making it easier to negotiate tight spaces and garden beds.

The GT 3200 boasts a cutting deck available in various sizes, including 48-inch and 54-inch options. This adaptability enables users to choose the size that best fits their mowing requirements. The deck is designed for efficiency, with dual-blade construction that delivers a clean, even cut across different grass types and terrain. Additionally, the deck’s adjustable cutting height allows for customized results, catering to users' specific aesthetic preferences.

Another notable characteristic of the Cub Cadet GT 3200 is its modular design, which allows for easy attachment of various implements. This versatility makes the GT 3200 suitable for multiple tasks, from mowing to snow clearing or tilling, as it can be equipped with a range of attachments such as snow blowers, front blades, and garden tillers.

Cub Cadet has integrated advanced technology in the GT 3200, including a digital gauge cluster that provides vital information at a glance, such as fuel levels and engine performance metrics. This technology enhances user experience and helps operators maintain optimal performance.

In terms of comfort, the GT 3200 comes with an ergonomic seat and intuitive controls, ensuring that operators can work for extended periods without discomfort. The high-back seat provides excellent support, and the easy-to-reach controls simplify operation, making mowing and gardening tasks less strenuous.

In summary, the Cub Cadet GT 3200 is a versatile, powerful, and technologically advanced garden tractor that offers a wide range of features designed to enhance performance and user experience. Whether for comprehensive lawn care or diverse landscaping tasks, the GT 3200 stands out as a top choice for those seeking quality and reliability in outdoor equipment.
Top Page Image Contents