Startup

Use this procedure whenever starting the pressure washer to help insure that the unit is ready to operate and starting is done safely.

1.Check oil levels.

Engine: Add SAE 30 or 10W–30 weight detergent oil as necessary.

Pump: Add SAE 20 or 30 weight non–detergent oil as necessary.

NOTE: Some units are equipped with a low–oil sensor that shuts the engine of f if the oil level falls below a certain level. If the unit stops unexpectedly, check both the oil and the fuel levels. Check the oil level each time the unit is refueled.

2. Check fuel level.

WARNING

DO NOT refuel a hot engine. Refueling a hot engine could cause a fire. Use only fresh, clean regular or unleaded gasoline. Close the fuel shutoff valve during refueling.

3. Turn on the water supply.

CAUTION

Never run the unit dry . Costly damage to the pump will result. Always be sure the water supply is completely turned on before operating.

4.Trigger the gun until water sprays from the tip indicating that the air is purged from the system.

5.Open the fuel shutof f valve and be sure the spark plug ignition cable is pushed firmly onto the spark plug. On those units equipped with an ignition shutoff switch, the switch should be in the “on” position. Throttle should be in the “run” position.

6.Start the engine.

NOTE: For easier starting, have one person start the pressure washer while another person triggers the spray gun.

If the engine is cold, completely close the engine choke. Grasp the starter rope, brace one foot on the pressure washer chassis and pull rope rapidly and firmly. Continue holding the rope as it returns. Pull and return the rope until the engine starts. In cool weather, the choke may have to be kept closed for 10 to 30 seconds before opening it to keep the engine running. Otherwise, open the choke as soon as the engine starts.

If the engine is warm, leave the choke open, or just partly close it. Start the engine as described in the preceding paragraph. When it starts, be sure to open the choke completely.

CAUTION

On recoil start engines, never let the starter rope return by itself. It could jam the recoil system.

7. ALWAYS engage the gun’ s trigger safety latch whenever you stop spraying, even for a moment, to reduce the risk of fluid injection or splashing in the eyes or on the skin if the gun is bumped or triggered accidentally.

8.ALWAYS observe the following CAUTIONS to avoid costly damage to the pressure washer.

CAUTION

DO NOT allow the pressure washer to idle for more than 10 minutes. Doing so may cause the recirculating water to overheat and seriously damage the pump. T urn of f the pressure washer if it will not be spraying or cleaning at least every 10 minutes. If heated inlet water is used, reduce this time further.

DO NOT run the pump dry , which will quickly damage the pump. Be sure the water supply is fully turned on before starting the pump.

DO NOT operate the pressure washer with the inlet water screen removed. This screen helps keep abrasive sediment out of the pump, which could clog or scratch the pump. Keep this screen clean.

DO NOT pump caustic materials; such materials may corrode the pump components.

9.See the chemical injector or sandblaster kit manual for detailed cleaning information if these accessories are used.

634

2245, 3035, 800-335, 800-065, 800-062 specifications

Graco Inc. has made significant strides in the manufacturing of fluid handling systems and equipment, positioning itself as a leader in the industry. Among their well-regarded products are the models 800-062, 308-501, 800-065, 800-335, and 3035. Each of these models comes with unique features and technologies that cater to various industrial applications.

The Graco 800-062 model is known for its reliability and efficiency in fluid transfer applications. It features a durable construction that withstands tough job site conditions. This model is equipped with advanced pneumatic technology, allowing for controlled fluid dispensing, which minimizes waste and enhances precision. Graco's attention to detail in ergonomics also enables operators to handle the device with comfort, reducing user fatigue during prolonged use.

The 308-501 model excels in its versatility, providing multiple output options to meet different operational needs. Its modular design allows for easy upgrades and maintenance. A standout characteristic of this model is its integrated filtration system, which ensures that the fluid remains contaminant-free, ultimately improving the quality of the application.

Moving on to the 800-065 model, this equipment is particularly known for its high flow rates and heavy-duty performance. Ideal for high-volume applications, it combines advanced hydraulic technology with a robust build, making it suitable for both indoor and outdoor environments. The automatic pressure regulation feature enhances its operational safety and extends the service life of the equipment.

The Graco 800-335 model stands out for its compact design, making it a perfect choice for workspaces with limited space. Despite its small footprint, it doesn't compromise on performance. The user-friendly interface allows for easy adjustments, and the model is equipped with low noise technology, making it ideal for noise-sensitive environments.

Finally, the Graco 3035 model is designed for precision and accuracy in fluid dispensing processes. It features intuitive controls and a state-of-the-art monitoring system, allowing for real-time feedback on fluid levels and pressure. An automatic shut-off feature ensures safety and prevents overfilling or accidental spills.

In summary, Graco Inc.'s models 800-062, 308-501, 800-065, 800-335, and 3035 represent a blend of innovation, durability, and user-centered design, making them vital tools in various industrial applications ranging from construction to manufacturing. These models not only enhance productivity but also ensure optimal operational safety, meeting the demands of a rapidly evolving industry.