Graco 3400 psi, Series B, 3600 psi, 3235, 3040, 800634, 800632 Troubleshooting, Problem Cause Solution

Page 14

Troubleshooting

Relieve the pressure (see page 5) before you proceed with troubleshooting.

PROBLEM

CAUSE

SOLUTION

 

 

 

Engine not starting or

No gasoline in fuel tank or carburetor

Fill the tank with gasoline, and open fuel shut off valve.

hard to start

 

Check fuel line and carburetor.

 

Low oil

Add oil to proper level.

 

Start/Stop switch in STOP position

Move switch to START position.

 

Water in fuel, or old fuel

Drain fuel tank and carburetor. Use new fuel, and make

 

 

sure dry spark plug is dry.

 

Engine flooded or improperly choked

Open choke, and crank engine several times to clear

 

 

out gas. Make sure spark plug is dry.

 

Dirty air cleaner filter

Remove and clean.

 

Spark plug dirty, wrong gap, or wrong type

Clean, adjust the gap, or replace.

 

Gun not triggered

Trigger gun while starting engine.

 

 

 

Engine missing or

Partially plugged air cleaner filter

Remove and clean.

lacking power

Spark plug dirty, wrong gap, or wrong type

Clean, adjust the gap, or replace.

 

 

 

 

Pressure too low

Worn or wrong size tip

Replace with tip of proper size.

and/or pump running

Inlet filter clogged

Clean. Check more frequently.

roughly

Worn packings, abrasives in water, or

Check filter. Replace packings. See Pump Service on

 

 

natural wear

page 8.

 

Inadequate water supply

Check water flow rate to pump.

 

Belts slipping

Tighten or replace; use correct belts, and replace both

 

 

at same time.

 

Fouled or dirty inlet or discharge valves

Clean inlet and discharge valve assemblies. Check filter.

 

Restricted inlet

Check if garden hose is collapsed or kinked.

 

Worn inlet or discharge valves

Replace worn valves. See Pump Service on page 8.

 

Leaking high-pressure hose

Replace high-pressure hose.

 

 

 

Water leaking from

Worn packings

Install new packings. See Pump Service on page 8.

under pump manifold

 

 

 

 

 

Water in pump oil

Humid air condensing inside crankcase

Change oil as specified in Maintenance on page 7.

 

Worn packings

Install new packings. See Pump Service on page 8.

 

Oil seals leaking

Install new oil seals. See Pump Service on page 8.

 

 

 

Packings failing

Scored, damaged, or worn plungers

Install new plungers. See Pump Service on page 8.

frequently or

Abrasive material in the fluid being

Install proper filtration on pump inlet plumbing.

prematurely.

pumped

 

 

 

 

Inlet water temperature too high

Check water temperature. It should not exceed

 

 

160_F (70_C).

 

Overpressurizing pump

Do not modify any factory-set adjustments. See

 

 

EQUIPMENT MISUSE HAZARD on page 3.

 

Excessive pressure due to partially

Clean or replace tip. See Installing and Changing

 

plugged or damaged tip

Spray Tips on page 6.

 

Pump running too long without spraying

Never run pump more than 10 minutes without spraying.

 

Running pump dry

Do not run pump without water.

 

 

 

Strong surging at inlet,

Foreign particles in the inlet or discharge

Clean or replace valves. See Pump Service on

and low pressure on

valve, or worn inlet and/or discharge

page 8.

discharge side

valves

 

 

 

 

14 308524

Image 14
Contents Pressure Washer Model 308524This manual contains important warnings and information Table of Contents SymbolsMoving Parts Hazard Check for Shipping Damage SetupSet Up Connect to Water SupplyStartup Pressure Relief ProcedureOperation Trigger Safety Latch Trigger Safety LatchInstalling and Changing Spray Tips Spray Tip Number Spray Pattern Fan AngleWater Sandblasting MaintenanceMaintenance Chart Shutdown, Flushing, and StoragePumping Section Pump ServiceValves Servicing the PlungersServicing the V-Packings Pressure Washer Parts Description Qty BlastingPump Parts Pump Parts Pump Repair KitsTroubleshooting Problem Cause SolutionTechnical Data 3235Toll Free Graco Standard WarrantyGraco Phone Number
Related manuals
Manual 12 pages 23.99 Kb Manual 40 pages 3.69 Kb Manual 20 pages 21.73 Kb Manual 14 pages 60.52 Kb

2900 psi, 2500 psi, 2545, 800629, 3000 psi specifications

Graco Series B, 288046 is a top-tier product designed to meet the rigorous demands of various applications in industries such as manufacturing, automotive, and construction. Renowned for its reliability and efficiency, this product stands out due to its innovative features and robust technology.

One of the standout features of the Graco Series B, 288046 is its advanced air-powered design. This design allows for smooth and consistent fluid transfer, minimizing downtime and enhancing productivity. The air-driven operation not only offers greater control over the flow rates but also ensures that the system can operate in situations where electric power may be unavailable or impractical. This versatility makes it ideal for various work environments.

The Series B is equipped with a high-performance motor that delivers exceptional power output while maintaining energy efficiency. This feature is particularly advantageous for businesses looking to reduce operational costs without compromising on performance. The motor is engineered to handle different fluid viscosities, making the Series B versatile for use with a wide range of materials, including paints, adhesives, and sealants.

Durability and ease of maintenance are key characteristics of the Graco Series B, 288046. Constructed from high-quality materials, the product is built to withstand harsh conditions, ensuring a long-lasting lifespan. Additionally, its modular design simplifies maintenance and repairs, allowing for quick replacements of components and minimal disruption to operations.

Safety is another paramount consideration incorporated into the Series B design. It features comprehensive safety mechanisms that protect users and equipment alike, reducing the risk of accidents during operation. This is especially crucial in environments where workers are regularly handling hazardous materials.

Graco also emphasizes user-friendly functionality. The Series B showcases intuitive controls, enabling operators to quickly familiarize themselves with the system and operate it efficiently. The product also includes adjustable pressure settings, allowing for precise application suited to specific tasks.

In conclusion, the Graco Series B, 288046 is an exemplary solution for companies seeking a reliable, efficient, and safe fluid handling system. With its advanced technologies, user-friendly features, and robust construction, it offers unmatched performance across various industries, ensuring optimal productivity and safety.