Craftsman 580.768020 Wash and Rinse Surface, Before Starting the Cleaning System, Add Engine Oil

,_	use the cleaning system from ladder,
	WARNING: Be extremely careful if you must
	scaffolding or any other relatively unstable
	location. When you press the trigger, the recoil
	from the initial spray could fume you to fall, or if
	you are too close to the cleaning surface, high
	pressure could force you off a climbing
	apparatus.

•Start at lower portion of area to be washed and work upward, using long, even overlapping strokes.

•Allow detergent to 'soakin'(between 3-5 minutes) before washing and rinsing. Reapply as needed to prevent surface from drying.

p

Wash and Rinse Surface

After you have applied detergent, scour the surface with the high pressure water stream and then rinse it clean, as follows:

•Pull adjustable nozzle backward to get high

pressure mode. Chemical will/net flow when in the high pressure mode.

•Expand the spray pattern for a more gentle rinsing "action. Start at top of area to be dnsed, working down with same action as for cleaning.

,_ CAUTION!cleaned.beMakeTest asuresmallthereareaisofrtothedamagesurface to caused by the high pressure spray.

RINSE SYSTEM AFTER EVERY USE

It is imperative that the chemical selector system be rinsed after each use to prevent clogging or leaks: ,

•Fill the System Rinse reservoir with clean water.

•Before disconnecting the water supply, start your cleaning system.

,_ System,CAUTION:makeBeforesurestartingyouhaveyourreadCleaningandfollowed the instructions in the sections "Before Starting the Cleaning System" on page 7 and =To Start the Cleaning System" on page 8.

•Push adjustable nozzle forward to get low pressure mode.

Rotate the Dial-A-Cleaner TM selector knob to the letter corresponding to the System Rinse tank. As clean rinse water is drawn through the }ystem,

continue the flow until no detergent foam is observed.

•Rotate the Dial-A-Cleaner TM selector knob to the

OFF position.

BEFORE STARTING THE CLEANING SYSTEM

To operatethe engine you willneed to do the following:

Add Engine Oil

Only use high quality detergent oil rated with API service classification SF or SG. Select the oil'sSAE

viscosity grade according to your expected operating temperature:

colder _ 32°F _ warmer

	I
5W30	SAE 30

Although multi-viscosity oils (5W30, 1OW3O, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used

above 32°F. Check your engine oil level more frequently to avoid possible damage from running low on oil.

•Place pressure washer system on a level surface

•Clean area around oil fill and remove oil dipstick.

•Wipe dipstick clean.

•Pour oil from enclosed bottle into the oil fill opening until oil reaches full mark on the dipstick. Stop and check the oil level periodically. Do not overfill.

•install oil dipstick, hand tighten securely.

Add Gasoline

•Use regular unleaded gasoline with the cleaning system engine. Fuel tank capacity is 1.5 U.S. quarts.

,_ fillDANGER!fueltank whenNever enginefillfuelistankrunningindoorshot.Never.Do not smoke when filling fuel tank.

,_ CAUTIONJleaveDoroomnotforoverfillexpansionthefuel.Alwaystank.

,_ CAUTION!fuelsExpedence(calledgasoholindicatesorusingthatblendedethanolalcohol or methanol) can attract moisture which leads to separation and formation of acids during

storage. Acidic gas can damage the fuel system of an engine while in storage.

To add fuel to engine:

•Clean area around fuel cap, remove cap.

•Add regular unleaded gasoline, slowly, to the fuel tank.

Important: Never mix oil with gasoline.

•Install fuel cap and wipe up any spilled gasoline.

7