Black & Decker PW1600 instruction manual Operation, Handle Assembly PW1750

bumps of wheel as shown and press center of wheel cap until it snaps securely to wheel.

4 PW1750

Handle Assembly - PW1750

Align and begin to push tubes of handle (K) down inside lower tubes (N) as shown. Press spring buttons (R) of handle (K) inward as handle tubes are pushed down fully into lower tubes (N), and both spring buttons protrude out through holes in lower tube (N) completing assembly.

5 PW1750

R

O

I

Upper Cord Wrap Hook Assembly - PW1750

Insert cord wrap top hook (M) into the rear slots in handle (K) by pushing upward and inward to snap in place. Drive two 1/2” self tapping screws included in cord hook bag through cord wrap holes into handle as shown until tight. DO NOT over tighten.

6 PW1750

SET-UP / ADJUSTMENT

Figure 7 - Insert the fan wand (D) into the gun wand (F) by pushing and rotating until the two parts are locked as shown in Figure 7.

7

Figure 8 - Connect the high pressure hose (F1) to the water (OUTLET) (A) on the unit by first inserting the brass end of the hose into the threaded outlet on the front of the unit, then snugly threading on the hose coupling.

8 High pressure hose

Figure 9 - Connect the garden hose quick connector (J) to your garden hose as shown in Fig. 9. The intake water temperature must NOT exceed 50°C (122°F). The water supply pressure must be between

20 and 80 psi.

CAUTION: The pressure washer must only be used with clean water; use of unfiltered water or corrosive chemicals will damage the pressure washer.

9

Figure 10 - With the quick connector (J) attached to your garden hose, pull back on its outer ring and push firmly onto the mating pump quick connector (B), (already attached to the pressure washer inlet), then release ring to engage.

10

IMPORTANT: The outer brass ring on the garden hose quick connector MUST be pulled back fully as shown in Fig. 11b) before pushing it over the pump quick connector (B). Water will not flow through to the pump if these 2 connectors are not fully coupled.

11

a)

Pump Quick

Connector

b)

Figure 12 - Connect other end of garden hose to the cold water source and turn water on full. This pressure washer is not intended to pump hot water. Never connect it to a hot water supply as it will significantly reduce the life of the pump.

12

OPERATION

NOTE: Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results. If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface.

This Pressure Washer is equipped with automatic delivery flow cut-off:

When the trigger is released, the dynamic pressure automatically stops the motor.

When the trigger is pressed, the internal pressure drop automatically starts the motor and the spray pressure is restored with a very slight delay.

Figure 13 - Ensure the on/off switch (I) is in the off position before plugging in the unit. Depress the switch portion marked “O” to ensure unit is off. Plug the Ground Fault Circuit Interrupter (GFCI) (G) into a power outlet. Indicator should turn red. TEST BEFORE EACH USE. Press the “TEST” button. Red indicator should disappear. Press “RESET” button again for use. Do not use if above test fails.

13

Figure 14 - Before each use, ensure the gun safety catch is released by pushing it down as shown, then press the trigger for a few seconds to allow air to escape and to discharge residual pressure in the hoses.

14

Figure 15 - Turn on the pressure washer by depressing the bottom half of the switch (I) marked “I”. The unit will run for a few seconds as it builds up pressure, then will shut off. It will run on demand as the gun trigger is depressed. Turn off the pressure washer by depressing the upper half of the switch marked “0”.

YOUR PRESSURE WASHER IS NOW READY TO USE - PLEASE REVIEW THE FOLLOWING FOR DETAILS ON ACCESSORIES APPLICATION.

15

O

I

6 7