Excell Precision VR2300 operation manual Storage, Engine Pump

Page 17

STORAGE

ENGINE

Consult the Engine Owners Manual for the manufacturer's recommendations for storage.

PUMP

It is recommended that you follow these steps to protect the internal seals of the pressure washer when STORING THE UNIT FOR MORE THAN 30 DAYS AND/OR

WHEN FREEZING TEMPERATURES ARE EXPECTED.

The manufacturer recommends using EXA80 Pump Saver/Winterizer. EXA80 Pump Saver/Winterizer may be purchased in stores where Excell pressure washers are sold. If EXA80 is not available, *RV antifreeze needs to be run through the pump as outlined in the steps below.

1.Obtain a funnel, six ounces of *RV antifreeze, and approximately 36 inches of garden hose with a male hose connector attached to one end.

Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump.

2.Disconnect spark plug wire.

3.Disconnect high pressure hose from pump and from spray gun.

4.Connect 36 inch length of hose to water inlet of pump.

5.Add *RV antifreeze to hose as shown.

6.Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump.

7.Remove short hose from water inlet of pump.

8.Reconnect spark plug wire.

9.Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle.

10.Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun/hose holder.

11.Store chemical hose, high pressure hose, spray gun, and wand so they are protected from damage, such as being run over.

*Windshield washer fluid may also be used.

17- ENG

D27935

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Pressure Washer Consumer Safety Information Table of ContentsSafety Guidelines / Definitions Risk to Breathing Important Safety InstructionsRisk of Explosion or Fire Risk of Chemical Burn Risk of Fluid InjectionRisk of HOT Surfaces Risk of Unsafe OperationRisk of Electrical Shock Risk of Injury from Spray Consumer General and Service InformationCarton Contents Assembly Instructions Screws Basic Elements of a Pressure Washer Operating InstructionsPressure Adjustments Pressure Washer Operating FeaturesBasic Elements of Engine Pressure Washer TerminologyHOW to USE Wand Read and Understand ALL Warnings Before Starting Unit HOW to Apply Chemicals and Cleaning SolventsStarting Engine Nozzle Cleaning MaintenanceHOW to Clean the Water Inlet Filter Engine Pump StorageProblem Cause Correction Trouble Shooting GuideAt pump Problem CauseWarranty ENG D27935 Call Quick Facts

VR2300 specifications

The Excell Precision VR2300 is a cutting-edge solution designed for precision machining, embodying advanced technologies and innovative features that set it apart in the competitive manufacturing landscape. Engineered for versatility and accuracy, the VR2300 is particularly well-suited for industries such as aerospace, automotive, and medical device manufacturing, where precision is paramount.

One of the standout features of the VR2300 is its robust structure, designed to withstand heavy workflows while maintaining dimensional stability. The machine is constructed with high-grade cast iron, which provides exceptional rigidity and dampens vibrations, ensuring that even the most intricate machining tasks yield high-quality results.

The VR2300 is equipped with a powerful spindle that operates at high speeds, allowing for efficient material removal and superior finish quality. With a speed range of 10,000 to 20,000 RPM, this machine is capable of handling a wide variety of materials, from aluminum alloys to hardened steels. The spindle is paired with an advanced cooling system, which maintains optimal operating temperatures, thus enhancing tool life and machining efficiency.

Another noteworthy technology featured in the VR2300 is its state-of-the-art CNC control system. The intuitive interface allows operators to program complex machining tasks with ease, minimizing setup times and maximizing productivity. The system also supports advanced features such as 3D simulation and predictive maintenance alerts, ensuring that potential issues are addressed before they cause downtime.

The VR2300 boasts an impressive axis travel range, which provides flexibility for a diverse range of applications. Its high-precision linear guides and ball screws deliver exceptional accuracy and repeatability, critical for producing intricate components. Furthermore, the machine comes equipped with an automatic tool changer (ATC), streamlining operations and reducing manual intervention.

Safety and efficiency are central to the design of the VR2300. It incorporates multiple safety features, including emergency stop buttons and protective enclosures, ensuring operator protection without compromising accessibility. Energy-efficient components also contribute to reduced power consumption, making the VR2300 an environmentally friendly choice.

Overall, the Excell Precision VR2300 is a powerful, versatile machining tool that combines robust construction, cutting-edge technology, and precision engineering, making it an ideal solution for manufacturers looking to enhance their capabilities and achieve superior results in their machining operations.
Top Page Image Contents