Excell Precision VR2300 operation manual Trouble Shooting Guide, Problem Cause Correction

Page 18

TROUBLE SHOOTING GUIDE

PROBLEM

CAUSE

CORRECTION

Engine will not start (see Engine Manual for further engine troubleshooting)

No fuel.

Pressure builds up after two pulls on the recoil starter or after initial use.

Choke lever in the “No Choke” position.

Spark plug wire not attached.

Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time.

Add Fuel.

Squeeze gun trigger to relieve pressure.

Move choke to the “Choke” position.

Attach spark plug wire.

Move choke to the “No Choke” position.

No or low pressure (initial use)

Wand not in high pressure.

Low water supply.

Leak at high pressure hose.

Nozzle obstructed.

Water filter screen clogged.

Defective E-Z start valve.

Air in hose.

Choke lever in the “Choke” position.

Throttle control lever is not in the “Fast” position.

High pressure hose is too long.

See How to Use Wand paragraph in the Operation Section.

Water supply must be at least 5 GPM @ 20 PSI.

Repair leak. Apply sealant tape if necessary.

Clean nozzle with paper clip or nozzle cleaning tool, pour water into nozzle end to flush out obstruction.

Remove and clean filter.

Check with Authorized Warranty Service Center (AWSC.)

Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re-connect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air

Move choke to the “No Choke” position.

Move throttle control lever to the “Fast” position.

Use high pressure hose under 100 feet.

D27935

18- ENG

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Pressure Washer Table of Contents Safety Guidelines / DefinitionsConsumer Safety Information Important Safety Instructions Risk of Explosion or FireRisk to Breathing Risk of Fluid Injection Risk of Chemical BurnRisk of Unsafe Operation Risk of Electrical ShockRisk of HOT Surfaces Consumer General and Service Information Risk of Injury from SprayCarton Contents Assembly Instructions Screws Operating Instructions Basic Elements of a Pressure WasherBasic Elements of Engine Pressure Washer Operating FeaturesPressure Adjustments Pressure Washer TerminologyHOW to USE Wand HOW to Apply Chemicals and Cleaning Solvents Read and Understand ALL Warnings Before Starting UnitStarting Maintenance Engine Nozzle CleaningHOW to Clean the Water Inlet Filter Storage Engine PumpTrouble Shooting Guide Problem Cause CorrectionProblem Cause At pumpWarranty ENG D27935 Quick Facts Call

VR2300 specifications

The Excell Precision VR2300 is a cutting-edge solution designed for precision machining, embodying advanced technologies and innovative features that set it apart in the competitive manufacturing landscape. Engineered for versatility and accuracy, the VR2300 is particularly well-suited for industries such as aerospace, automotive, and medical device manufacturing, where precision is paramount.

One of the standout features of the VR2300 is its robust structure, designed to withstand heavy workflows while maintaining dimensional stability. The machine is constructed with high-grade cast iron, which provides exceptional rigidity and dampens vibrations, ensuring that even the most intricate machining tasks yield high-quality results.

The VR2300 is equipped with a powerful spindle that operates at high speeds, allowing for efficient material removal and superior finish quality. With a speed range of 10,000 to 20,000 RPM, this machine is capable of handling a wide variety of materials, from aluminum alloys to hardened steels. The spindle is paired with an advanced cooling system, which maintains optimal operating temperatures, thus enhancing tool life and machining efficiency.

Another noteworthy technology featured in the VR2300 is its state-of-the-art CNC control system. The intuitive interface allows operators to program complex machining tasks with ease, minimizing setup times and maximizing productivity. The system also supports advanced features such as 3D simulation and predictive maintenance alerts, ensuring that potential issues are addressed before they cause downtime.

The VR2300 boasts an impressive axis travel range, which provides flexibility for a diverse range of applications. Its high-precision linear guides and ball screws deliver exceptional accuracy and repeatability, critical for producing intricate components. Furthermore, the machine comes equipped with an automatic tool changer (ATC), streamlining operations and reducing manual intervention.

Safety and efficiency are central to the design of the VR2300. It incorporates multiple safety features, including emergency stop buttons and protective enclosures, ensuring operator protection without compromising accessibility. Energy-efficient components also contribute to reduced power consumption, making the VR2300 an environmentally friendly choice.

Overall, the Excell Precision VR2300 is a powerful, versatile machining tool that combines robust construction, cutting-edge technology, and precision engineering, making it an ideal solution for manufacturers looking to enhance their capabilities and achieve superior results in their machining operations.
Top Page Image Contents