Briggs & Stratton 1903 Connect Hose and Water Supply to Pump, Checklist Before Starting Engine

Page 8

Section 3: Assembly

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

NOTE: Your pressure washer comes with a quick connect that you can use to attach the high pressure hose to either the pump or spray gun.

1.Uncoil high pressure hose and attach female quick connect to one end of hose.Attach male quick connect to high pressure fitting on pump (Figure 7).

Figure 7 — Attach Quick Connect

2.Attach high pressure hose to high pressure outlet on pump (Figure 8). Pull down on collar of quick connect, slide fitting into pump and let go of collar. Pull on hose to be sure of a tight connection.

Figure 8 — Connect High Pressure Hose to Pump

NOTE: The quick connect is shown connecting the high pressure hose to the pump. If you choose to use the quick connect for the gun to hose connection, follow the same directions to attach quick connect from gun to hose.

3.Attach other end of hose to base of spray gun (Figure 9).Tighten by hand.

Figure 9 — Connect High Pressure Hose to Spray Gun

Connect high

pressure hose

here

4.Before connecting garden hose to water inlet, inspect inlet screen (Figure 10). Clean screen if it contains debris, replace if damaged. DO NOT RUN PRESSURE WASHER IF SCREEN IS DAMAGED.

Figure 10 — Connect Garden Hose to Water Inlet

Inspect inlet

screen, DO

NOT use if

damaged, clean

if dirty.

5.Run water through garden hose for 30 seconds to clean out any debris.Turn off water.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

6.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 10).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

7.Turn ON water and squeeze trigger on spray gun to purge pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate eye protection.

Checklist Before Starting Engine

Review the unit’s assembly to confirm you have performed all of the following:

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in engine crankcase.

3.Add proper fuel to fuel tank.

4.Check for properly attached hose connections.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Questions? Preguntas? Helpline 1-888-611-6708 M-F8-5 CT Manual No GS Revision 1 12/17/2003Equipment Description Table of ContentsSafety Rules When Transporting or Repairing Equipment High pressure spray may damage fragile items including glass Know Your Pressure Washer Features and Controls SectionSafety Goggles not shown Always use the enclosed Preparing Pressure Washer for USE AssemblyAssembly Add Engine Oil and Fuel Handle Align Holes SupportsChecklist Before Starting Engine Connect Hose and Water Supply to PumpConnect high Screen, doHOW to USE Your Pressure Washer How to Stop Pressure WasherOperation Section To Start Pressure WasherHow to Use Accessory Tray How to Use Spray TipsOperation Low PressureCleaning and Applying Chemical Pressure Washer RinsingAutomatic Cool Down System Thermal ReliefPressure Washer Maintenance Section MaintenanceGeneral Maintenance Recommendations Maintenance Nozzle MaintenanceRing Maintenance Purge Pump of Air ContaminantsEngine Maintenance Pump MaintenanceData Tag Changing Pump OilAlways wear eye protection when using PumpSaver StoragePreparing the Unit for Storage Storing the EnginePage Problem Cause Correction TroubleshootingTroubleshooting Section Exploded Views and Parts Lists Exploded View and Parts List UnitDescription Items Not Illustrated DescriptionExploded Views and Parts Lists Exploded View and Parts List PumpReglas de Seguridad Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadSección 1 Reglas de Seguridad PeligroPrecaución Características y Controles Conozca SU Maquina Lavadora DE PresionFiltro de Aire Perilla del Cebador Usada para arranque de motores fríosPreparando EL Lavador a Presión Para SU USO MontajeMontaje Sección 3 Montaje Agregar Aceite al Motor y GasolinaManubrio Alinear Orificios Soportes del Coloque la lavadora a presión sobre una superficie niveladaConecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorPresión Deposite la gasolina adecuada en el tanque del combustibleOperación Cómo Usar SU Máquina Lavadora a PresiónCómo Darle Arranque a su Máquina Lavadora a Presión Cómo Parar su Lavador a PresiónSección 4 Operación Enjuage de la Máquina Lavadora a Presión Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Maquina Lavadora a Presion MantenimientoRecomendaciones Generales Sección 5 Mantenimiento Elimine el Aire y los Contaminantes de la BombaMantenimiento de la Boquilla Mantenimiento de los Anillos OEtiqueta de Datos Mantenimiento DEL MotorMantenimiento de la Bomba Almacenamiento Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaDiagnosticos de Averías Reparacion DE DañosEfectiva desde el 12 ro de Noviembre Equipo Para Uso Del Consumidor Para Uso ComercialGenerador Portátil AñoTROY-BILT Owner Warranty Policy Effective November 12 About your equipment warrantyEquipment Consumer Use Commercial Use Portable Generator Years 2nd year parts only

1903 specifications

Briggs & Stratton Corporation, founded in 1903, has established itself as a prominent name in the field of small engine manufacturing. Headquartered in Milwaukee, Wisconsin, the company initially focused on producing gas engines for a variety of applications. Over the years, it has evolved into a leading manufacturer of outdoor power equipment engines, which are widely used in lawn mowers, pressure washers, and other gardening tools.

One of the defining features of Briggs & Stratton's products is their commitment to durability and reliability. The engines are designed with high-quality materials and precision engineering, ensuring that they can withstand the rigors of both residential and commercial use. Many models are equipped with overhead valve (OHV) technology, which enhances engine performance by improving airflow, resulting in better fuel efficiency and reduced emissions.

Another significant innovation introduced by Briggs & Stratton in the early 2000s is the ReadyStart system. This user-friendly technology eliminates the need for a choke, making starting the engine simpler and more reliable. With ReadyStart, the engine adjusts itself automatically for different weather conditions, ensuring a hassle-free start every time.

In terms of performance, Briggs & Stratton engines are known for their power and torque. Models vary in horsepower ratings, catering to different needs—from small residential applications to heavy-duty commercial usage. The engines feature a wide range of power options, helping consumers select an engine that suits their specific requirements.

The company has also made strides in environmental sustainability. Briggs & Stratton has focused on reducing emissions through advanced engineering, adhering to strict environmental regulations while not compromising on performance. Their engines often integrate technologies such as low-oil shutdown, which protects the engine from damage due to insufficient lubrication.

Customer support and service have always been priorities for Briggs & Stratton. The company provides extensive resources, including manuals, maintenance tips, and customer service support, ensuring that users can maximize the performance and lifespan of their equipment.

Overall, Briggs & Stratton's legacy since its inception in 1903 is one of innovation, quality, and performance. The combination of advanced technologies, durable design, and customer-oriented support positions Briggs & Stratton as a leader in the small engine market, continuing to meet the evolving needs of consumers and professionals alike.
Top Page Image Contents