Briggs & Stratton HU80931, HU80530 manual Features, Assembly

Page 8

FEATURES

KNOW YOUR PRESSURE WASHER

See Figure 1.

The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.

BRIGGS & STRATTON ENGINE

This Briggs & Stratton 500 Series engine enables the pres- sure washer to achieve 2,200 PSI (pounds per square inch) at a rate of 2.0 GPM (gallons per minute).

FUEL TANK

This fuel tank has a maximum capacity of 1 quart (.95 liters). Use unleaded automotive gasoline in the engine.

HOSE STORAGE

Once the high pressure hose is rolled, hang it on the front of the machine using the hook and loop strap for convenient storage.

OFF SWITCH

To turn the engine off, press and hold the OFF switch for a full three seconds or until the engine stops.

RECOIL STARTER

The recoil starter is pulled to start the machine.

SPRAY WAND

The spray wand has a gripping surface that provides added control of the spray wand and helps reduce fatigue. Both the spray wand and extension have storage areas located on top of the machine.

THERMAL RELIEF VALVE

This pump feature will prevent water temperatures from reaching harmful levels by releasing a small amount of water from a rubber hose. Once the water has drained, the thermal relief valve will reset itself.

TRIGGER WITH LOCK OUT

Pulling the trigger releases a stream of water for high pressure cleaning. The lock out provides protection against unauthorized use.

ASSEMBLY

UNPACKING

This product requires assembly.

Carefully cut the box down the sides then remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included.

NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

Do not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

If any parts are damaged or missing, please call 1-866-340-3912 for assistance.

PACKING LIST

Pressure Washer

20 ft. High Pressure Hose Spray Wand Assembly (upper) Spray Wand Extension (lower) Quick-Connect Nozzle (3) Nozzle Cleaning Tool Injection Hose

Wheel (2)

Flat Washer (4) Axle (2)

Hitch Pin (2)

4-Cycle Engine Oil (SAE 30) Telescoping Handle Operator’s Manual

8

Image 8
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionImportant Safety Instructions Read ALL Instructions Before Using this ProductSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONAuthorized Service Center for repair. When servic ServiceSymbol Signal Meaning Product Specifications OIL CAPDipstick Telescoping Handle Spray Wand Extension High Pressure HoseFeatures AssemblyAttaching the Wheel Assembly Installing the Telescoping HandleAxle Handle Lock CAP Push to InsertAdding OIL to the Engine Adding Gasoline to the Fuel TankOIL CAP Dipstick Funnel Fuel CAPConnecting High Pressure Hose to Spray Wand Assembly Attaching Injection HoseAssembling the Spray Wand To attach the spray wand extensionConnecting the High Pressure Hose to Pump Connecting the Garden Hose toOperation Pressure WasherStarting and Stopping the Pressure Washer Recoil Starter OFF SwitchApplications Using the Spray Wand Trigger Selecting the Right QUICK-CONNECT Nozzle for the JOBMoving the Pressure Washer Storing the Pressure WasherWashing with Detergent Rinsing with the Pressure WasherMaintenance General MaintenanceCleaning the AIR Filter TOP View AIR Filter Screw Shroud CoverNozzle Maintenance Pump MaintenanceChanging the OIL Checking a Fouled Spark PlugPreparing for USE After Storage Troubleshooting Problem Cause SolutionPage Warranty Limited NON-ENGINE Warranty StatementService California Proposition