Briggs & Stratton HU80931 Operation, Connecting the High Pressure Hose to Pump, Pressure Washer

Page 12

ASSEMBLY

CONNECTING THE HIGH PRESSURE HOSE TO

 

THE PUMP

COLLAR

See Figure 9.

 

������After the high pressure hose has been uncoiled and attached

 

to the spray wand:

 

Align the collar on the threaded nipple on the pump.

 

Insert the nozzle on the end of the high pressure hose

 

collar into the threaded nipple.

 

Turn the collar clockwise to tighten the hose securely to the pump.

Pull on the hose to be certain it is properly secured.

CONNECTING THE GARDEN HOSE TO THE

THREADED

PRESSURE WASHER

NIPPLE

See Figure 10.

Fig. 9

The water supply must come from a water main. NEVER

WATER

use hot water or water from pools, lakes, etc. Before

INTAKE

connecting the garden hose to the pressure washer:

 

Run water through the hose for 30 seconds to clean any

 

debris from the hose.

 

Inspect the screen in the water intake.

 

If the screen is damaged, do not use the machine until

GARDEN

the screen has been replaced.

HOSE

If the screen is dirty, clean it before connecting the garden hose to the machine.

������To connect the garden hose to the machine:

Uncoil the garden hose.

NOTE: There must be a minimum of 10 feet of

 

 

unrestricted hose between the pressure washer intake and

SCREEN

 

the hose faucet or shut off valve (such as a “Y” shut off

Fig. 10

connector).

 

 

 

With the hose faucet turned completely off, attach the end of the garden hose to the water intake. Tighten by hand.

OPERATION

WARNING:

Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not recom- mended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

WARNING:

Do not direct discharge stream at persons. Failure to heed this warning could result in serious injury.

12

Image 12
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionImportant Safety Instructions Read ALL Instructions Before Using this ProductSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningAuthorized Service Center for repair. When servic Product Specifications OIL CAPDipstick Telescoping Handle Spray Wand Extension High Pressure HoseFeatures AssemblyAttaching the Wheel Assembly Installing the Telescoping HandleAxle Handle Lock CAP Push to InsertAdding OIL to the Engine Adding Gasoline to the Fuel TankOIL CAP Dipstick Funnel Fuel CAPConnecting High Pressure Hose to Spray Wand Assembly Attaching Injection HoseAssembling the Spray Wand To attach the spray wand extensionConnecting the High Pressure Hose to Pump Connecting the Garden Hose toOperation Pressure WasherRecoil Starter OFF Switch ApplicationsStarting and Stopping the Pressure Washer Using the Spray Wand Trigger Selecting the Right QUICK-CONNECT Nozzle for the JOBMoving the Pressure Washer Storing the Pressure WasherWashing with Detergent Rinsing with the Pressure WasherMaintenance General MaintenanceCleaning the AIR Filter TOP View AIR Filter Screw Shroud CoverNozzle Maintenance Pump MaintenanceChanging the OIL Checking a Fouled Spark PlugPreparing for USE After Storage Troubleshooting Problem Cause SolutionPage Warranty Limited NON-ENGINE Warranty StatementService California Proposition