Briggs & Stratton 20263 manual Unintentional sparking can result in fire or electric shock

Page 4

Section 1: Safety Rules

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

ALWAYS point gun in safe direction and squeeze spray gun trigger, to release pressure and avoid kickback each time, before starting engine. Engage trigger lock when not in use.

When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

After each starting attempt, where engine fails to run, always point gun in safe direction and squeeze spray gun trigger to release high pressure.

Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when gun kicks back.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

DO NOT touch hot surfaces and avoid hot exhaust gases.

Allow equipment to cool before touching.

Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead.

Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

WARNING

Starter and other rotating parts can entangle hands, hair, clothing, or accessories.

DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

NEVER aim spray gun at people, animals or plants.

DO NOT allow CHILDREN to operate pressure washer.

NEVER repair high pressure hose. Replace it.

NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

Keep high pressure hose connected to pump and spray gun while system is pressurized.

ALWAYS point gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

Before starting the pressure washer, be sure you are wearing adequate safety goggles.

WARNING

Unintentional sparking can result in fire or electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER

Disconnect spark plug wire from spark plug and place wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

DO NOT check for spark with spark plug removed.

4

Image 4
Contents 020263 3100 PSI Safety Rules Table of ContentsEquipment Description When Adding Fuel Operate pressure washer only outdoorsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Safety Goggles not shown Always use the enclosedKnow Your Pressure Washer Nozzle Extension with Quick Connect Allows you toAssembly Assembly SectionPreparing Pressure Washer for USE Assembly Attach Chemical Hose to PumpAdd Engine Oil and Fuel Attach chemical hose to chemical injection fitting on pumpChecklist Before Starting Engine Connect Hose and Water Supply to PumpHere Not use ifHOW to USE Pressure Washer Section OperationPressure Washer Location To Start Your Pressure WasherHow to Stop Your Pressure Washer Safety LatchEngage trigger lock on spray gun when not in use OperationHow to Use Accessory Tray How to Use ProjectPro Nozzle SystemFollow these instructions to change ProjectPro nozzles Engage trigger lock on spray gunRust removal or other stubborn substances tar Patio furniture, lawn equipment, etc., select yellowGum, grease, wax, etc., select red Max Delicate ProjectPro nozzle FigureCleaning and Applying Detergent Pressure Washer RinsingAutomatic Cool Down System Thermal ReliefMaintenance Section SpecificationsGeneral Maintenance Recommendations Pressure Washer MaintenanceMaintenance Engine MaintenanceNozzle Maintenance Ring MaintenanceStorage Preparing Unit for StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Page Page Limited Warranty Reglas de Seguridad Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadSección 1 Reglas de Seguridad Cuando Añada CombustibleCuando Pruebe LA Bujía DEL Motor Precaución Características y Controles Conozca SU Maquina Lavadora a PresionMontaje MontajePreparando EL Lavador a Presión Para SU USO Sección 3 Montaje Montaje de Manguera de Productos Químicos a BombaAgregar Aceite al Motor y Gasolina Coloque la lavadora a presión sobre una superficie niveladaConecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoOperación Cómo Usar SU Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Lavadora a PresiónCómo Parar su Lavador a Presión Sección 4 OperaciónEl Pasador de la Seguridad Utilización de la Bandeja de Accesorios Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja La Presión AltaElija la boquilla ProjectPro que desee Figura 39 Boquilla SuaveLimpieza y Aplicación del Químico Enjuage de la Máquina Lavadora a PresiónSistema de Enfriamiento Automático Alivio Térmico On Posición Off PosiciónMantenimiento EspecificacionesRecomendaciones Generales Antes de Cada UsoSección 5 Mantenimiento Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de los Anillos OSección 6 Almacenamiento Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaDiagnosticos de Averías Reparacion DE DañosNotas Garantía Limitada

20263 specifications

Briggs & Stratton 20263 is a powerful and efficient engine model known for its reliability and performance in a variety of outdoor applications. This engine is particularly popular for use in lawn mowers, pressure washers, and other outdoor power equipment, thanks to its robust design and advanced features that make it a preferred choice among both homeowners and professionals.

One of the standout features of the Briggs & Stratton 20263 engine is its overhead valve (OHV) technology. This design provides better airflow and enhances fuel efficiency, allowing the engine to deliver more power while consuming less fuel. This efficiency not only reduces operational costs but also minimizes emissions, making it an environmentally friendly option.

Additionally, the 20263 model is equipped with a recoil start mechanism and an integrated fuel system, which ensures easy starting and smooth operation. The engine’s 206 cc displacement provides ample power for tough tasks, and the high torque output allows it to maintain performance under heavy loads.

The construction of the Briggs & Stratton 20263 engine is designed to withstand harsh conditions. It features a durable cast iron sleeve that enhances the engine's longevity and reduces wear over time. Furthermore, the engine is equipped with a dual-sealed air filter that helps protect the internal components from dust and debris, ensuring consistent performance and reliability.

Another remarkable characteristic of the 20263 model is its low vibration technology. This feature helps reduce operator fatigue, making it more comfortable to use for extended periods. The engine is also designed to operate quietly, significantly minimizing noise pollution, which is especially important for residential areas.

Moreover, the Briggs & Stratton 20263 engine supports a variety of attachments and accessories, making it versatile for numerous outdoor applications. Whether you need an engine for lawn care or cleaning, its comprehensive compatibility is a significant advantage.

In summary, the Briggs & Stratton 20263 engine combines power, efficiency, and durability. With its innovative technologies, ease of use, and reliable performance, it stands out as a top choice for anyone in need of a robust outdoor power solution.