Briggs & Stratton 20263 Connect Hose and Water Supply to Pump, Checklist Before Starting Engine

Page 9

Section 3: Assembly

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 6).Tighten by hand.

Figure 6 — Connect High Pressure Hose to Spray Gun

Connect high

pressure hose

here

NOTE: Remove and discard all pump shipping caps before attaching hoses.

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 7).Tighten by hand.

Figure 7 — Connect High Pressure Hose to Pump

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 8). Clean screen if it contains debris or replace if damaged. Refer to “O-Ring Maintenance” section if inlet screen is damaged. DO NOT run pressure washer if inlet screen is damaged.

Figure 8 — Connect Garden Hose to Water Inlet

Inspect inlet

screen, DO

NOT use if

damaged, clean

if dirty.

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 8).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON water, point gun in a safe direction and squeeze trigger to purge pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

Before starting the pressure washer, be sure you are wearing adequate safety goggles.

Checklist Before Starting Engine

Review the unit’s assembly to confirm you have performed all of the following:

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in engine crankcase.

3.Add proper fuel to fuel tank.

4.Check for properly attached hose connections.

5.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Pressure Washer” before using pressure washer.

9

Image 9
Contents 020263 3100 PSI Table of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Safety Goggles not shown Always use the enclosed Section Features and ControlsKnow Your Pressure Washer Nozzle Extension with Quick Connect Allows you toAssembly Section AssemblyPreparing Pressure Washer for USE Attach Chemical Hose to Pump AssemblyAdd Engine Oil and Fuel Attach chemical hose to chemical injection fitting on pumpConnect Hose and Water Supply to Pump Checklist Before Starting EngineHere Not use ifSection Operation HOW to USE Pressure WasherPressure Washer Location To Start Your Pressure WasherSafety Latch How to Stop Your Pressure WasherEngage trigger lock on spray gun when not in use OperationHow to Use ProjectPro Nozzle System How to Use Accessory TrayFollow these instructions to change ProjectPro nozzles Engage trigger lock on spray gunPatio furniture, lawn equipment, etc., select yellow Rust removal or other stubborn substances tarGum, grease, wax, etc., select red Max Delicate ProjectPro nozzle FigurePressure Washer Rinsing Cleaning and Applying DetergentAutomatic Cool Down System Thermal ReliefSpecifications Maintenance SectionGeneral Maintenance Recommendations Pressure Washer MaintenanceEngine Maintenance MaintenanceNozzle Maintenance Ring MaintenancePreparing Unit for Storage StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Page Page Limited Warranty Tabla DE Contenidos Reglas de SeguridadDescripción DEL Equipo Reglas DE SeguridadCuando Añada Combustible Sección 1 Reglas de SeguridadCuando Pruebe LA Bujía DEL Motor Precaución Conozca SU Maquina Lavadora a Presion Características y ControlesMontaje MontajePreparando EL Lavador a Presión Para SU USO Montaje de Manguera de Productos Químicos a Bomba Sección 3 MontajeAgregar Aceite al Motor y Gasolina Coloque la lavadora a presión sobre una superficie niveladaLista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoCómo Usar SU Lavadora a Presión OperaciónUbicación del Lavadora a Presión Cómo Darle Arranque a su Lavadora a PresiónSección 4 Operación Cómo Parar su Lavador a PresiónEl Pasador de la Seguridad Cómo Usar el Sistema de Boquillas ProjectPro Utilización de la Bandeja de AccesoriosLa Presión Baja La Presión AltaFigura 39 Boquilla Suave Elija la boquilla ProjectPro que deseeEnjuage de la Máquina Lavadora a Presión Limpieza y Aplicación del QuímicoSistema de Enfriamiento Automático Alivio Térmico On Posición Off PosiciónEspecificaciones MantenimientoRecomendaciones Generales Antes de Cada UsoMantenimiento DEL Motor Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de los Anillos OPreparando LA Unidad Para SU Almacenamiento Sección 6 AlmacenamientoAlmacenando EL Motor Proteger la BombaReparacion DE Daños Diagnosticos de AveríasNotas Garantía Limitada

20263 specifications

Briggs & Stratton 20263 is a powerful and efficient engine model known for its reliability and performance in a variety of outdoor applications. This engine is particularly popular for use in lawn mowers, pressure washers, and other outdoor power equipment, thanks to its robust design and advanced features that make it a preferred choice among both homeowners and professionals.

One of the standout features of the Briggs & Stratton 20263 engine is its overhead valve (OHV) technology. This design provides better airflow and enhances fuel efficiency, allowing the engine to deliver more power while consuming less fuel. This efficiency not only reduces operational costs but also minimizes emissions, making it an environmentally friendly option.

Additionally, the 20263 model is equipped with a recoil start mechanism and an integrated fuel system, which ensures easy starting and smooth operation. The engine’s 206 cc displacement provides ample power for tough tasks, and the high torque output allows it to maintain performance under heavy loads.

The construction of the Briggs & Stratton 20263 engine is designed to withstand harsh conditions. It features a durable cast iron sleeve that enhances the engine's longevity and reduces wear over time. Furthermore, the engine is equipped with a dual-sealed air filter that helps protect the internal components from dust and debris, ensuring consistent performance and reliability.

Another remarkable characteristic of the 20263 model is its low vibration technology. This feature helps reduce operator fatigue, making it more comfortable to use for extended periods. The engine is also designed to operate quietly, significantly minimizing noise pollution, which is especially important for residential areas.

Moreover, the Briggs & Stratton 20263 engine supports a variety of attachments and accessories, making it versatile for numerous outdoor applications. Whether you need an engine for lawn care or cleaning, its comprehensive compatibility is a significant advantage.

In summary, the Briggs & Stratton 20263 engine combines power, efficiency, and durability. With its innovative technologies, ease of use, and reliable performance, it stands out as a top choice for anyone in need of a robust outdoor power solution.