Briggs & Stratton 01988-1 manual Checklist Before Starting Engine, Screen. do not

Page 9

Section 3: Assembly

Figure 4 — Connect High Pressure Hose to Spray Gun

Connect high pressure hose here.

NOTE: Remove and discard all pump shipping caps before attaching hoses.

2.Similarly, attach other end of high pressure hose to the high pressure outlet on pump. Pull down on collar of quick connect, slide onto pump and let go of collar. Pull on hose to be sure of a tight connection.

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 5). Clean screen if it contains debris or replace if damaged. Refer to the section “O-Ring Maintenance” if inlet screen is damaged. DO NOT run pressure washer if inlet screen is damaged.

Figure 5 — Connect Garden Hose to Water Inlet

Inspect inlet

screen. DO NOT

use if damaged;

clean if dirty.

4.Run water through garden hose for 30 seconds to clean out any debris.Turn off water.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 5).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON water and squeeze trigger on spray gun to purge pump system of air and debris.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate eye protection.

Checklist Before Starting Engine

Review the unit’s assembly to confirm you have performed all of the following:

1.Make sure handle is secure.

2.Make sure oil dipstick is installed into pump.

3.Check for properly tightened hose connections.

4.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

5.Check that oil has been added to proper level in engine crankcase.

6.Add proper fuel to fuel tank.

7.Provide a proper water supply (not to exceed 100°F).

8.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Antes de utilizar el producto, lea este manual AdvertenciaTable of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Know Your Pressure Washer Section Features and ControlsNozzle Extension with Quick Connect Choke LeverAssembly Assembly SectionCarton Contents Preparing Pressure Washer for USEAttach Handle AssemblyAdd Engine Oil and Fuel Connect Hose and Water Supply to PumpScreen. do not Checklist Before Starting EngineHow to Start Engine HOW to USE Pressure WasherSection Operation Pressure Washer LocationOperation How to Stop Pressure WasherCleaning and Applying Chemical How to Use Spray TipsPressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief Discharging the warm water onto the groundSpecifications Section MaintenanceGeneral Maintenance Recommendations Pressure Washer MaintenanceEngine Maintenance MaintenanceNozzle Maintenance Ring MaintenancePreparing the Unit for Storage StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingPage Year Consumer Use Years Years orConserve Estas Instrucciones Reglas de SeguridadCuando Añada Combustible Sección 1 Reglas de SeguridadCuando Pruebe LA Bujía DEL Motor Precaución Conozca SU Maquina Lavadora DE Presion Características y ControlesMontaje MontajePreparando EL Lavador a Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeConecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorCómo Usar SU Lavadora a Presión OperaciónUbicación del Lavadora a Presión Cómo Darle Arranque a su Lavadora a PresiónCómo Parar su Lavador a Presión Sección 4 OperaciónLimpieza y Aplicación del Químico Cómo Usar las Puntas de RociadoDetergentes caseros podrían dañar la bomba Usada para Aplicar QuímicosEnjuage de la Máquina Lavadora a Presión Limpiando el TuboSistema de Enfriamiento Automático Alivio Térmico Especificaciones MantenimientoRecomendaciones Generales Mantenimiento DE LA Lavadora a PresionMantenimiento DEL Motor Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de los Anillos OPreparando LA Unidad Para SU Almacenamiento AlmacenamientoAlmacenando EL Motor Proteger la BombaProblema Diagnosticos de AveríasReparacion DE Daños SoluciónNotas Garantía Limitada

01988-1 specifications

The Briggs & Stratton 01988-1 is a powerful and versatile portable generator designed to provide reliable electrical power in various situations, such as during power outages, outdoor events, or construction sites. Known for its durability and performance, this generator is favored by both homeowners and professionals alike.

One of the key features of the Briggs & Stratton 01988-1 is its robust engine. Powered by a reliable Briggs & Stratton overhead valve (OHV) engine, the generator delivers a substantial amount of power, with a starting wattage of 8000 watts and a running wattage of 6500 watts. This ensures that it can handle multiple appliances simultaneously, whether it’s keeping the lights on during an unexpected blackout or powering tools on a job site.

The generator is also equipped with a durable, metal frame that provides stability and protection, making it suitable for various outdoor conditions. Its compact design and wheels make it easy to transport, which is an added advantage for users who need to move it frequently.

In terms of technology, the Briggs & Stratton 01988-1 features a convenient electric start system, which allows for quick and easy start-up with just the push of a button. This eliminates the hassle often associated with traditional pull-start generators, especially in cold weather. Additionally, the generator comes with an automatic low oil shut-off feature, ensuring that the engine is protected from damage and prolonging its lifespan.

Another notable characteristic of the 01988-1 is its fuel efficiency. Designed to operate on standard gasoline, it provides extended run times, allowing for longer periods of uninterrupted power. The built-in fuel gauge ensures users can easily monitor fuel levels, making it more user-friendly.

Further enhancing its usability are multiple outlets, including 120V household outlets and 120/240V twist-lock outlets, allowing for versatile connections for various devices and appliances. This makes the generator not only useful for emergency situations but also ideal for recreational activities such as camping and tailgating.

Overall, the Briggs & Stratton 01988-1 stands out as a reliable and efficient generator, combining powerful performance with user-friendly features. Its durability, portability, and advanced technology make it a solid choice for anyone in need of dependable power solutions.
Top Page Image Contents