Briggs & Stratton 01936 General Maintenance Recommendations, Pressure Washer Maintenance

Page 12

Pressure Washer

GENERAL MAINTENANCE RECOMMENDATIONS

The pressure washer warranty does not cover items that have been subjected to operator abuse or negligence.To receive full value from the warranty, the operator must maintain the pressure washer as instructed in this manual.

•Some adjustments will need to be made periodically to properly maintain your pressure washer.

•All maintenance in this manual and the engine owner’s manual should be made at least once each season.

•If equipped with inflatable tires, keep the air pressure at the value marked on the tire or within 15 and 40 psi.

PRESSURE WASHER

MAINTENANCE

Check In-Line Filter

Refer to Figure 22 and service the in-line filter if it becomes clogged, as follows:

Figure 22 — Clean In-Line Filter

Filter Screen

Nozzle Extension

O-ring

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and nozzle extension with clean water to clear debris.

2.If screen is damaged, the o-ring kit contains a replacement in-line filter screen and an o-ring. If undamaged, reuse screen.

3.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push the screen in with eraser end of pencil until it rests flat at bottom of opening.Take care to not bend screen.

4.Place o-ring into threaded end of extension. Push o-ring snugly against in-line filter screen.

5.Assemble nozzle extension to spray gun, as described earlier in this manual.

Check and Clean Inlet Screen

Examine the screen on the water inlet. Clean it if the screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING! NEVER repair a high pressure hose. Replace it with another hose that exceeds the maximum pressure rating of your pressure washer.

Check Chemical Injection Hose

Examine the filter on the detergent tube and clean if clogged.The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Gun and Nozzle Extension

Examine the hose connection to the spray gun and make sure it is secure.Test the trigger by pressing it and making sure it “springs back” into place when you release it. Put the safety latch in the ON position and test the trigger.You should not be able to press the trigger.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 01805 2500 PSI 01806 2650 PSI 01936 2550 PSI Table of Contents Safety RulesHazard Symbols and Meanings Equipment DescriptionWhen Transporting or Repairing Equipment High pressure spray may damage fragile items including glass Assembly Preparing Pressure Washer for USERemove Pressure Washer From Carton Attach Handle to UnitInstall J Hook on Accessory Tray Add Engine Oil Add FuelTo attach handle supplied with two L hooks Model Checklist Before Starting Engine Connect Hose and Water Supply to PumpModel HOW to USE Your HOW to USE NozzlesHow to Start Pressure Washer How to Stop Pressure WasherIf Unit is Equipped with Adjustable Nozzle Cleaning and Applying ChemicalFollow these instructions to change spray tips To apply detergent follow these stepsCleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal Relief Discharging the warm water onto the groundGeneral Maintenance Recommendations Pressure Washer MaintenanceNozzle Maintenance Adjustable nozzleOrifice Quick-connect spray tipsEngine Maintenance Ring MaintenancePump Maintenance Purge Pump of Air ContaminantsPreparing the Unit for Storage Storing the EngineTroubleshooting Problem Cause CorrectionOUR Equipment Tabla DE Contenidos Descripción DEL EquipoInstrucciones DE Seguridad AdvertenciaPeligro Cuando Añada CombustiblePrecaución Montaje Preparando EL Lavador a Presión Para SU USORemueva el Lavador a Presión del Empaque Conecte el ManubrioPara Conecte el Manubrio con Dos Perno L Modelo Gancho del PistolaAgregar Aceite al Motor Añada GasolinaConecte la Manguera y el Suministro de Agua a la Bomba Lista DE Revision Previa AL Arranque DEL Motor Modelo01806 Cómo Usar SU Lavadora a Presión Cómo Usar LAS BoquillasCómo Darle Arranque a su Lavadora a Presión Cómo Detener su Lavadora a PresiónSi la Unidad Está Equipada con la Boquilla Regulable Limpieza y Aplicación del QuímicoPara cambiar las boquillas Detergentes caseros podrían dañar la bombaEnjuage de la Máquina Lavadora a Presión Limpiando el Tubo de Sifón del DetergenteSistema de Enfriamiento Automático Alivio Térmico Lave de 1 a 2 minutosRecomendaciones Generales Mantenimiento DE LA Lavadora a PresionElimine el Aire y los Contaminantes de la Bomba Mantenimiento de los Anillos OBoquillas con conector rápido Para retirar el aire de la bomba, siga los siguientes pasosMantenimiento DEL Motor Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Mantenimiento de la BombaReparacion DE Averias Garantía Limitada 01936 2550 PSI Exploded View and Parts List Main Unit PSI Pressure WasherDescription Items Not Illustrated DescriptionExploded View and Parts List Pump Include all parts shown within the box
Top Page Image Contents