Zenoah PSZ2401 manual OP7 OP8, Adjust the pump as follows, Oil tank Chain cover, Cable adjuster

Page 38

English

8. Operation

OP7

OP8

.04 in

(1~2mm) (1)

The guide bar and chain are lubricated automatically by a pump that operates whenever the chain rotates. The pump is set at the factory to deliver a minimum flow rate, but it can be adjusted in the field. A temporary increase in oil flow is often desirable when cutting things like hardwood or wood with a lot of pitch.

Adjust the pump as follows:

1.Stop the engine and make sure the stop switch is in the OFF position.

2. Place the unit on its side with the oil res ervoir up. (OP7)

(1)Oil tank

(2)Chain cover

IMPORTANT

The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw.

3.With a screwdriver, push in on the oil flow rate adjusting screw and turn in the desired direction (there are three incremental settings):

(a)Clockwise-decrease lubrication.

(b)Counter clockwise-increase lubrication.

(c)Middle

■ADJUSTING THROTTLE CABLE

•The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP8)

(1) Cable adjuster

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents PSZ2401 PSZ2401-CA Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido PSZ2401/PSZ2401-CA SpecificationsParts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique PSZ2401-CA/PSZ2401-CASymbols on the machine Importante Working Circumstance For safe operationWorking Condition Precauciones Conditions DE TravailCondiciones DE Trabajo Working Plan Before Starting the EngineLA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheStarting the Engine Demarrage DU Moteur Arranque DEL MotorIf Someone Comes Using the ProductMaintenance Check okEntretien Mantenimiento SI QUELQU’UN S’APPROCHESI Alguien SE Aproxima Tout est en ordre de marcheHandling Fuel Refill after cooling the engineLlenar una vez que el motor se haya enfriado Manipulation DU CarburantManipulación DEL Combustible Transportation Kickback and Pinching SafetyPrecautions Beware of kickback Beware of pinchingRetroceso Y Pellizco Tenga cuidado con el retroceso Precautions DE Securite Contre LE Rebond ET LE PincementPrecauciones DE Seguridad DE Tenga cuidado con el pellizcoFor safe operation Importante Set up Fixation DU Mecanisme DE Debrouissaillage SE4 Raccordement Cable ’ACCELERATEURRaccordement DES Fils Electriques Conexión DEL Alambre DEL AceleradorPay attention to the correct direction of the saw chain Chain tension adjusting screw Loosen TightenSE5 SE6 SE7 SE8 Hole Moving direction Chain tensioner nutGaine de protection comme suit De engranaje como sigue Assemblage MontajeUn paquet standard de cette tronçonneuse contient les Agujero Dirección de movimiento Tuerca de tensión de cadenaSE9 Balance UnitUnite DE Balance Unidad DE BalanceRecommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel and Chain Oil Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite Rapport DE Melange Recommande Essence 50 HuileLors de l’utilisation de la véritable huile RedMax/ZENOAH Al utilizar el aceite auténtico de RedMax/ZENOAHFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadChain OIL Huile Pour Chaîne Aceite Para LA CadenaOP5 Starting Engine OperationOP1 OP2 OP3 Levier du starter Combustible Huile pour chainetteCombustible Aceite para cadena Fermé Cerrar Ouvert AbrirStopping Engine OP4 Adjusting OIL Flow RateOP6 Checking OIL SupplyReglage DU Debit D’HUILE Arret DU Moteur OP4 Cómo Parar EL Motor OP4Contrôle DU Graissage DE LA Chaîne Control DEL Suministro DE AceiteCable adjuster Adjust the pump as followsAdjusting Throttle Cable OP7 OP8Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorOP9 Adjusting Idling Speed OP9 Idle adjusting screwAjuste DE LA Velocidad DE Marcha EN Vacío OP9 Reglage DU Ralenti OP9Vis de réglage du ralenti Tornillo de ajuste de marcha mínimaMaintenance Maintenance ChartTabla DE Mantenimiento MantenimientoTableau D’ENTRETIEN Guide BAR MA1 MA2 MA3 MA4 MA5Oiling Port OthersPignon Barre Guide Barra DE GuíaDivers Otros Rueda DentadaChain type 90SG File size 32 in 4.0mm MA6 MA7 MA8SAW Chain Type de chaîne 90SG Taille de la lime 5/32 de pouce 4.0mm Méihode et critères daffûtagePorter des gants de sécurité Avant laffûtage Normas para el ajuste de los dientesAIR Filter Replacement Plug is a Champion RZ7CMA9 Fuel FilterEntretien Mantenimiento Gear Case MA13 MufflerSpark Arrester MA12 Grease fittingOuïe DU Refroidissement PAR AIR PARE-ETINCELLES MA12Gaine Protectrice MA13 Parachispas MA12Disposal Procedures to be Performed After Every 100 Hours of USEStorage Cylinder Intake air cooling vent backCilindro Toma de aire de refrigeración posterior Procedure a Effectuer Toutes LES 100 Heures D’UTILISATIONMortes et autres débris avant d’utiliser la machine Procedimientos a Realizar Cada Horas DE USOGuide de localisation des pannes Troubleshooting guide13. Guía de localización y solución de problemas PSZ2401 PSZ2401-CA NotaParts list Pipe Comp Engine Unit PSZ2401/PSZ2401-CA S/N 60600101 and up Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Page Page PSZ2401 Emission ControlMesures DE Lutte Contre Control DE Emisiones LES Emissions PSZ2401-CA

PSZ2401 specifications

The Zenoah PSZ2401 is a robust and efficient chainsaw designed for both professional and amateur use. Known for its reliability and performance, this model is particularly favored in the forestry industry, landscaping, and for residential purposes.

One of the main features of the Zenoah PSZ2401 is its lightweight design, which ensures easy handling and maneuverability. Weighing in at around 5.6 kg (approximately 12.3 lbs), it allows users to operate the chainsaw for extended periods without experiencing excessive fatigue. This is especially beneficial for professionals involved in tree trimming and logging operations, where prolonged use is common.

The PSZ2401 is powered by a high-performance Zenoah engine that delivers impressive cutting power. With a displacement of 24.0 cc, the engine combines efficiency with strong torque, making it capable of cutting through various types of wood with ease. Its air-cooled, two-stroke engine technology not only ensures optimal performance but also contributes to lower emissions, aligning with environmental standards.

Another standout feature is the automatic chain lubrication system. This technology maintains a consistent oil supply to the chain and bar, reducing wear and tear and extending the lifespan of the cutting components. Additionally, the tool-less chain tensioning system makes adjustments quick and straightforward, allowing users to achieve the desired tension without the need for extra tools.

The ergonomic design of the Zenoah PSZ2401 enhances user comfort. It features a wrap-around front handle and an anti-vibration system that minimizes shock during operation. This results in reduced operator fatigue, enabling longer periods of use while maintaining precision and control.

Safety is a critical aspect of the Zenoah PSZ2401, and it is equipped with several safety features. These include a chain brake system that stops the chain instantly in case of kickback and a throttle lockout that prevents accidental throttle engagement. These features provide peace of mind and contribute to safer operation in demanding environments.

Overall, the Zenoah PSZ2401 is a well-engineered chainsaw that excels in power, efficiency, and user-friendly design. Its combination of advanced technologies, durability, and safety features makes it an excellent choice for both novice users and seasoned professionals, ensuring that it remains a reliable tool in any cutting endeavor.
Top Page Image Contents