Zenoah SRTZ2401F manual Handling Fuel, Refill after cooling the engine, Transportation

Page 18

English

5. For safe operation

those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

■HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine.

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 10 feet or more away from where it was refueled before turning on the engine.

■TRANSPORTATION

1.When you finish trimming in one location and wish to continue work in another spot, turn off the engine, lift up the unit and carry it paying attention to the blade.

2.Never forget to place the protective cover over the blades.

3.When transporting the unit over long distances, detach the blade and fix the unit by ropes.

4.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

18

Image 18

Contents SRTZ2401F SRTZ2401F-CA Information Informationinformación Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Symbols on the machine Wear head, eye and ear protectionPosition Emplacement PosiciónFor safe operation Working ConditionWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineLA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL ProductoMaintenance If Someone ComesTout est en ordre de marche SI QUELQU’UN S’APPROCHE SI Alguien SE AproximaEntretien MantenimientoHandling Fuel Refill after cooling the engineTransportation Llenar una vez que el motor se haya enfriado Manipulation DU CarburantManipulación DEL Combustible TransportAttaching the Trimming Mechanism SE2 Set upSE1 SE2 Installing Handle Balance UnitInstalación DEL Mango Assemblage MontajeMise EN Place DE LA Poignee Equilibrage DE LA MachineWhen using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 OP3 OP4 Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Ajuste DE LA Velocidad DE Marcha EN Vacío OP6Operation Fonctionnement Uso Maintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoQuick TIP MA1Blades MA1 MA2Entretien Mantenimiento AIR Filter Replacement Plug is a NGK CMR7HMA3 MA4 MA5 Fuel FilterFiltre a Carburant Filtro DE Combustible Filtre a AIRFiltro DE Aire Bougie D’ALLUMAGE BujíaSpark arrester Muffler MA6Spark Arrester Intake AIR Cooling VentParachispas PARE-ETINCELLESOuïe DU Refroidissement PAR AIR Toma DE Aire DE RefrigeraciónDisposal Procedures to be Performed After Every 100 Hours of USEStorage MA7 MA8Mise au rebut Eliminación Procedure a Effectuer Toutes LES 100 Heures D’UTILISATIONRangement Almacenamiento Procedimientos a Realizar Cada 100 Horas DE USOTroubleshooting guide 12. Guía de localización y solución de problemasGuide de localisation des pannes Lista de piezas NotaParts list Cutting Unit SRTZ2401F/SRTZ2401F-CA S/N Z000001 and up Engine Unit SRTZ2401F/SRTZ2401F-CA S/N 60100101 and up Qty Key# Part Number Description Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Mesures DE Lutte Contre LES Emissions Emission ControlSRTZ2401F Control DE Emisiones