Zenoah PSZ2600 Fuel and chain oil, Recommended Mixing Ratio Gasoline 50 OIL, HOW to MIX Fuel

Page 9

6. Set up

4.Adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail.

(1) Chain tension adjusting screw

(a) Loosen

(b) Tighten

5.Tighten the mounting nut securely with the bar tip held up (TORQUE: 8.9 ~ 11.7 N.m./90 ~ 120 kg-cm). Then check the chain for smooth rotation and correct tension while mov- ing it by hand. If necessary, readjust.

PSZ2600

7. Fuel and chain oil

FUEL

 

 

 

 

WARNING

 

 

• Gasoline is very flammable. Avoid smoking or

G

bringing any flame or sparks near fuel. Make sure

to stop the engine and allow it cool before refuel-

B

ing the unit. Select outdoor bare ground for fueling

 

and move at least 3 m (10 ft) away from the fueling

 

point before starting the engine.

 

The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle en- gine use (JASO FC GRADE OIL or ISO EGC GRADE).

Do not use BIA or TCW (2-stroke water-cooling type) mixed oil.

(1) Tighten

WARNING

It is very important to maintain the proper chain tension. Rapid wear of the guide bar or the chain coming off eas- ily can be caused by improper tension. Especially when using a new chain, take good care of it since it should expand when first used.

BALANCE UNIT

1.Put on strap and attach unit to strap.

2.Depending on the working posture, slide clamp up or down until unit balances and the strap fits your body.

RECOMMENDED MIXING RATIO GASOLINE 50 : OIL 1

(when using ZENOAH genuine oil)

Exhaust emission are controlled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the introduc- tion of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89RON (USA/Canada: 87AL).

If you use a gasoline of a lower octane value than pre- scribed, there is a danger that the engine tempera- ture may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

WARNING

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate de- pending on oil ingredients, sufficient agitation is neces-

GB-9

Image 9
Contents GB-1 PSZ260025.4 cm 94 dBA 109 dBA 114 dBA LpA LwA Idling Racing MeasuredGB-2 1st JuneParts location ContentsSymbols on the machine SpecificationFor safe operation Before Starting EngineGB-5 Maintenance Using the ProductGB-6 Starting the EngineGB-7 Kickback Safety Precautions For Chain SAW UsersHandling Fuel TransportationGB-8 Set upFuel and chain oil HOW to MIX FuelFuel Recommended Mixing Ratio Gasoline 50 OILFueling the Unit OperationFor Your Engine LIFE, Avoid Chain OILAdjusting Idling Speed Adjusting Throttle Cable~ 2 mm GB-11Checking oil supply GB-12Maintenance GB-14 GB-15 25 0.65 mmSprocket SAW ChainLimited warranty Troubleshooting guideStorage Disposal

PSZ2600 specifications

The Zenoah PSZ2600 is a versatile and robust handheld power tool designed for a variety of outdoor tasks, particularly in landscaping and gardening. This model stands out in the market due to its blend of advanced technology, user-friendly features, and outstanding performance.

One of the main features of the Zenoah PSZ2600 is its powerful engine. The unit is equipped with a highly efficient 25.4cc two-stroke engine that delivers impressive power while maintaining low fuel consumption. This engine is not only designed for high performance but also for environmental responsibility, meeting stringent emissions regulations without sacrificing power output.

The PSZ2600 boasts a lightweight design, making it easy to handle during prolonged use. Weighing in at just over 5 kg, it reduces the strain on the user, allowing for extended periods of work without excessive fatigue. Its ergonomic design includes a comfortable handle and a well-balanced body, enhancing maneuverability and ease of operation.

Another notable characteristic of the PSP2600 is its advanced vibration-damping technology. This feature minimizes vibrations during operation, which not only improves user comfort but also increases control over the tool. This technology is particularly beneficial during extended use, reducing the risk of fatigue-related injuries.

The Zenoah PSZ2600 also offers a variety of attachments, making it a multifunctional tool. Its compatibility with several accessories enables users to transform it into a hedge trimmer, brush cutter, or pole saw, catering to diverse gardening and landscaping needs. This versatility makes it an excellent investment for both professionals and homeowners alike.

Ease of maintenance is another key aspect of the Zenoah PSZ2600. The tool includes a tool-less air filter cover, allowing for quick and easy access for cleaning or replacement. The fuel system is designed for easy refueling, further enhancing the user experience.

Overall, the Zenoah PSZ2600 stands as a testament to innovative engineering in handheld power tools. Its powerful engine, lightweight design, user-oriented features, and versatility make it an exceptional choice for anyone looking to tackle outdoor projects with efficiency and ease. Whether you're a professional landscaper or a gardening enthusiast, the PSZ2600 is designed to meet your needs effectively.