Zenoah BK2651DL owner manual Operation, Starting a Cooled Engine, Starting a Warmed Engine

Page 10

BK2651DL

8. Operation

STARTING A COOLED ENGINE

1.Set the ignition switch to the RUN position.

2.Release the throttle lever. This lever cannot be oper- ated unless you hold the grip firmly and push the up- per lever as far as it goes.

(3) (2)

(1)

Ignition switch

(1)

 

(2) STOP

 

(3) RUN

 

(4) Throttle lever

 

(5)

Idling

 

(6)

Fully opened

 

(6)

(4) (5)

3.Fill the carburetor with fuel by using the carburetor starting pump. Repeatedly push and release the pump with the fingers until excess fuel flows out in the clear tube.

NOTE

•The pumping operation is not required when restart- ing the engine immediately after stopping it while fuel remains in the tank.

4. Close the choke lever at the bottom of the air cleaner.

NOTE

•Pull the starter rope while leaving the choke open if you restart the engine immediately after the engine stops.

Choke lever

Primer pump

Open Close

5.Place the unit on flat, firm ground. Make sure that the cutting head is clear of everything around it, then pull the starter knob while grasping the main pipe with the left hand and weighing down the frame with the right foot.

IMPORTANT

•Do not pull all the rope at a time or return it by releas- ing the knob. Doing so may cause a starter failure.

6.When the engine starts, open the choke gradually.

7.Allow the engine to warm up at low speed for two to three minutes before starting operation.

IMPORTANT

•Overchoking may make the engine hard to start due to excess fuel. If the engine fails to start after several attempts, open the choke and repeatedly pull the rope, or remove the spark plug and dry it before trying again.

STARTING A WARMED ENGINE

You can start a warmed engine while carrying the unit on the back.

1.Set the ignition switch to the RUN position.

2.Release the throttle lever.

3.Set the choke lever to the Open position.

4.Hold the handle firmly with the right hand and keep the cutter head away from surroundings such as the ground.

5.Pull the starter grip with the left hand.

Starter grip

GB-10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents BK2651DL EC Declaration of Comformity Contents Parts locationSpecification Symbols on the ma- chineWorking Circumstance For safe operationWorking Condition Working PlanBefore Starting Engine Using the ProductStarting the Engine Handling Fuel MaintenanceIf Someone Comes TransportationSet up Fuel Starting a Cooled Engine OperationStarting a Warmed Engine Adjusting Idling Speed Adjusting Throttle CableStopping Engine Cutting Work Putting on the UnitTrimming Grass and Weeds Adjusting the Line Length MaintenanceRefilling Trimming Line Fuel Filter Replacement Plug is a NGK BPMR7AAIR Filter MufflerDisposal Procedures to be Performed After Every 100 Hours of USEStorage Intake AIR Cooling VentLimited warranty Troubleshooting guideCheck Probable Causes Action

BK2651DL specifications

The Zenoah BK2651DL is a powerful and versatile petrol-powered brush cutter, designed for both professional landscapers and homeowners seeking an efficient tool for tackling various outdoor maintenance tasks. Known for its reliability and performance, the BK2651DL combines innovative technology with user-friendly features to deliver outstanding results.

One of the standout characteristics of the Zenoah BK2651DL is its robust 25.4cc engine. This dual-cycle engine provides a perfect balance of power and fuel efficiency, ensuring users can complete their tasks without frequent interruptions for refueling. The engine utilizes a specially designed intake system, enhancing airflow for better combustion, which translates into improved power output and reduced emissions.

Ergonomics play a significant role in the design of the BK2651DL. The brush cutter features an adjustable handle, allowing for customized operation angles tailored to the user's height and preference. This not only enhances comfort during prolonged use but also minimizes operator fatigue. The lightweight design of the unit, weighing only around 5.3 kilograms, further contributes to ease of handling and maneuverability in tight spaces.

Another defining feature of the Zenoah BK2651DL is its low vibration technology. This innovation significantly reduces the amount of vibration transmitted to the user’s hands and arms, making it an ideal choice for extended use, particularly for those who regularly engage in heavy-duty tasks. Additionally, the machine incorporates a sophisticated anti-kickback system, which increases safety by stabilizing the tool during operation.

The BK2651DL is designed with a quick-release attachment system, facilitating the easy interchange of different cutting blades and accessories. This versatility allows users to switch from cutting grass to tackling thicker brush or even small trees effortlessly. The dual-line cutting head simplifies line replacement, making maintenance straightforward and efficient.

In conclusion, the Zenoah BK2651DL is an exceptional brush cutter that excels in performance, comfort, and adaptability. Its powerful engine, ergonomic features, and advanced technologies make it suitable for a variety of tasks, making it a valuable tool for anyone looking to maintain their landscape efficiently. With Zenoah's commitment to quality and innovation, the BK2651DL stands out as an excellent choice in the competitive market of outdoor power equipment.
Top Page Image Contents