Zenoah GZ7000 manual Cutting equipment designed to reduce kickback, Bar, Chain

Page 10

GENERAL SAFETY PRECAUTIONS

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating ! saw chain can cause extremely serious

injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

Length (inches/cm)

Number of teeth on bar tip sprocket (T).

Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

Chain pitch (inches)

Drive link width (mm/inches)

Number of drive links.

10 – English

Image 10
Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents What is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting a spike bumper AssemblyFitting the bar and chain Protect your hands from injuryFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburettorHigh speed jet H Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Must always be replacedRunning when making adjustments Adjustment of the oil pumpDust Free centrifugal cleaning Needle bearing lubricationWinter use Temperature 0C or colderFitting the winterising kit Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataApplies to Europe only Bar and chain combinationsSaw chain filing and file gauges EC-declaration of conformity EN ISO 12100-22003, Cispr 122005, EN ISOLimited Warranty Limited warranty1151332-26