Zenoah GZ7000 Air ﬁlter, Spark plug, Lubricating the bar tip sprocket, Must always be replaced

Page 33

MAINTENANCE

Air ﬁlter

The air ﬁlter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts.

•Excessive fuel consumption.

•Remove the air ﬁlter after taking off the air ﬁlter cover. When reﬁtting make sure that the air ﬁlter seals tightly against the ﬁlter holder. Clean the ﬁlter by brushing or shaking it.

The ﬁlter can be cleaned more thoroughly by washing it in water and detergent.

An air ﬁlter that has been in use for a long time cannot be cleaned completely. The ﬁlter must therefore be replaced with a new one at regular intervals. A damaged air ﬁlter

must always be replaced.

Spark plug

The spark plug condition is inﬂuenced by:

•Incorrect carburettor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air ﬁlter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difﬁculties.

If the machine is low on power, difﬁcult to start or runs poorly at idle speed: always check the spark plug ﬁrst before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is ﬁtted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

English – 33

Image 33

Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents What is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMufﬂer General rulesBar Cutting equipment designed to reduce kickbackChain Injuries Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain AssemblyFitting a spike bumper Protect your hands from injuryFuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral High speed jet H Correctly adjusted carburettorChecking brake band wear Checking the front hand guardImmediately Checking the inertia brake releaseMufﬂer Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air ﬁlterLubricating the bar tip sprocket Must always be replacedDust Free centrifugal cleaning Adjustment of the oil pumpRunning when making adjustments Needle bearing lubricationTemperature 0C or colder Winter useFitting the winterising kit Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain ﬁling and ﬁle gauges EC-declaration of conformity Bar and chain combinationsApplies to Europe only EN ISO 12100-22003, Cispr 122005, EN ISOLimited warranty Limited Warranty1151332-26