Sears 917.29149 Service and Adjustments, Tiller, To Adjust Handle Height, Tine Arrangement

Page 14

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT

Factory assembly has provided lowest handle height. Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

1.If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets.

2.Slide handle panel to desired location.

3.Tighten the four nuts securely.

Engine Brackets

Handle

Panel

Nuts(Also 2 on Left Side of Tiller

TINE ARRANGEMENT

Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs.

CAUTION: Tines are sharp. Wear gloves or other protection when handling tines.

NORMAL TILLING - 24" PATH

•Assemble holes “A” in tine hubs to holes “B” in tine shaft.

Clevis Pin

Outer Tine

A

A

B

 

tine_4

B

 

Hairpin Clip

Inner Tine

 

MID-WIDTH TILLING - 22" PATH

•Assemble holes “A” in tine hubs to holes “C” in tine shaft.

A C C A

tine_5

NARROW TILLING/CULTIVATING - 12-3/4" PATH

• Remove outer tines.

tine_6

Inner Tines Only

NOTE: When reassembling outer tines, be sure right tine assembly (marked “R”) and left tine assembly (marked “L”) are mounted to correct side of tine shaft.

TINE OPERATION CHECK

WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation.

For proper tine operation, tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the “OFF” (up) position. If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip.

FINAL CHECK “OFF” POSITION

1.With tine control “OFF” (up), push down on handle to raise tines off the ground.

2.Slowly pull recoil starter handle while observing tines. Tines should not rotate.

3.If tines rotate, inner wire of control cable is too tight which is extend- ing lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring ten- sion. Tighten cable clip.

4.Recheck in “OFF” position and adjust if necessary.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Front Tine Tiller Safety Rules Table of ContentsWarranty Maintenance and Storage OperationCustomer Responsibilities Product SpecificationsSears Installation Service Repair Protection AgreementsAccessories Unassembled PartsASSEMBLY/PRE-OPERATION Operation Know Your TillerTilling HOW to USE Your TillerStopping Depth StakeTo Start Engine ADD GasolineCultivating Breaking in Your TillerTilling Hints General Recommendations MaintenanceLubrication Chart Before Each USELubrication AIR CleanerEngine To Change Engine OILSpark Plug CleaningCooling System TransmissionTiller Service and AdjustmentsTo Adjust Handle Height Tine ArrangementTo Replace V-BELT To Adjust CarburetorTo Remove Belt Guard Fuel System StorageOther Engine OILTroubleshooting Chart Problem Cause CorrectionEngine Page Get it fixed, at your home or ours

917.29149 specifications

The Sears 917.29149 is a lawn tractor that exemplifies efficiency and durability, making it a popular choice for homeowners and landscaping professionals alike. Designed to tackle a variety of mowing tasks, this robust machine boasts several key features and technologies that enhance its functionality and ease of use.

One of the standout characteristics of the Sears 917.29149 is its powerful engine. It typically comes equipped with a dependable gas engine that provides ample power and torque, allowing it to handle not just mowing but also towing and hauling tasks. This makes it suitable for larger properties where versatility is essential. The engine is designed for reliability, enabling users to tackle tough grass and uneven terrain without compromising performance.

The cutting deck of the Sears 917.29149 is another significant attribute. Equipped with a wide cutting width, typically around 42 to 54 inches, it allows for efficient mowing in fewer passes, saving time and effort. The cutting height can usually be adjusted easily, offering users the ability to customize their mowing height according to the seasonal requirements of their lawn. This level of customization is crucial for maintaining a healthy lawn while also accommodating different grass types.

In terms of maneuverability, the Sears 917.29149 features a well-designed steering system that allows for easy navigation around obstacles. The turning radius is tight, making it simple to mow around trees, flower beds, and other landscaping elements without leaving uncut patches of grass. The comfortable seat and ergonomic controls ensure that users can operate the tractor for extended periods without fatigue.

Technologically, the Sears 917.29149 may include advanced features such as a hydrostatic transmission. This system provides seamless speed adjustments without the need for manual gear shifting, making operation smoother and more intuitive. Additionally, models may offer features like cruise control, allowing the operator to maintain a consistent speed, which is particularly useful for larger mowing jobs.

Moreover, the tractor’s attachment compatibility further enhances its utility, enabling users to add accessories such as bags for grass clippings, snow plows, or other tools for year-round use. This transforms the lawn tractor into a multifunctional piece of equipment, capable of handling various yard maintenance tasks.

Overall, the Sears 917.29149 stands as an exemplary lawn tractor that combines power, efficiency, and versatility. Its well-thought-out features and technologies make it a reliable choice for anyone looking to maintain their lawn with ease and precision. Whether for residential use or light commercial tasks, this tractor represents a solid investment for effective lawn care.
Top Page Image Contents