To Remove Belt Guard, To Replace V-BELT

FINAL CHECK “ON” POSITION

5.With tine control “ON” (held down to handle) push down on handle to raise tines off the ground.

6.Slowly pull recoil starter handle while observing tines. Tines should rotate forward.

7.If tines do not rotate, inner wire of con- trol cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip.

8.Recheck in “ON” position and adjust if necessary.

NOTE: If “ON” position check required adjustment, recheck “OFF” position ad- justment to insure tines do not rotate when control is “OFF” (up).

Tine Control “OFF” Position

Body

Tine Control “ON” Position

Tine Control Cable

Cable Clip

TO REMOVE BELT GUARD

1.Remove screws from side of belt guard.

2.Pull belt guard out and away from unit.

3.Replace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely.

Belt

Guard

Screw

TO REPLACE V-BELT

Replace V-belt if it has stretched consid- erably or if it has cracks or frayed edges.

1.Belt guard must be removed to ser- vice belt. See “TO REMOVE BELT GUARD” in this section of manual.

BELT REMOVAL

2.Remove V-belt from transmission pul- ley ﬁrst and then from engine pulley.

BELT REPLACEMENT

3.Install new V-belt to engine pulley ﬁrst then to transmission pulley. Be sure belt is positioned on inside groove of both pulleys, inside all belt guides and rests on idler pulley.

CHECK TINE OPERATION

4.See “TINE OPERATION CHECK” in this section of manual.

5.Replace belt guard

Belt Guide

Engine

Pulley

Belt Guide	V-Belt	Transmission
Belt Guide	Idler Pulley
	Idler Pulley
		Pulley

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, engine performance can be affected by differences in fuel, tem- perature, altitude or load. If the carburetor does need adjustment, contact your near- est authorized service center/department IMPORTANT: Never tamper with the engine governor, which is factory set

for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact your nearest sears or other qualiﬁed service center which has the proper equipment and experience to make any necessary adjustments.

917.29149 specifications

The Sears 917.29149 is a lawn tractor that exemplifies efficiency and durability, making it a popular choice for homeowners and landscaping professionals alike. Designed to tackle a variety of mowing tasks, this robust machine boasts several key features and technologies that enhance its functionality and ease of use.

One of the standout characteristics of the Sears 917.29149 is its powerful engine. It typically comes equipped with a dependable gas engine that provides ample power and torque, allowing it to handle not just mowing but also towing and hauling tasks. This makes it suitable for larger properties where versatility is essential. The engine is designed for reliability, enabling users to tackle tough grass and uneven terrain without compromising performance.

The cutting deck of the Sears 917.29149 is another significant attribute. Equipped with a wide cutting width, typically around 42 to 54 inches, it allows for efficient mowing in fewer passes, saving time and effort. The cutting height can usually be adjusted easily, offering users the ability to customize their mowing height according to the seasonal requirements of their lawn. This level of customization is crucial for maintaining a healthy lawn while also accommodating different grass types.

In terms of maneuverability, the Sears 917.29149 features a well-designed steering system that allows for easy navigation around obstacles. The turning radius is tight, making it simple to mow around trees, flower beds, and other landscaping elements without leaving uncut patches of grass. The comfortable seat and ergonomic controls ensure that users can operate the tractor for extended periods without fatigue.

Technologically, the Sears 917.29149 may include advanced features such as a hydrostatic transmission. This system provides seamless speed adjustments without the need for manual gear shifting, making operation smoother and more intuitive. Additionally, models may offer features like cruise control, allowing the operator to maintain a consistent speed, which is particularly useful for larger mowing jobs.

Moreover, the tractor’s attachment compatibility further enhances its utility, enabling users to add accessories such as bags for grass clippings, snow plows, or other tools for year-round use. This transforms the lawn tractor into a multifunctional piece of equipment, capable of handling various yard maintenance tasks.

Overall, the Sears 917.29149 stands as an exemplary lawn tractor that combines power, efficiency, and versatility. Its well-thought-out features and technologies make it a reliable choice for anyone looking to maintain their lawn with ease and precision. Whether for residential use or light commercial tasks, this tractor represents a solid investment for effective lawn care.