Poulan MRT500 owner manual Safety Rules, Training, Preparation, Operation, Maintenance and Storage

Page 2

SAFETY RULES

SAFE OPERATION PRACTICES FOR WALK-BEHIND POWERED ROTARY TILLERS

TRAINING

Read the Owner’s Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

Keep the area of operation clear of all persons, par- ticularly small children, and pets.

PREPARATION

Thoroughly inspect the area where the equipment is to be used and remove all foreign objects.

Disengage all clutches and shift into neutral before starting the engine (motor).

Do not operate the equipment without wearing ade- quate outer garments. Wear footwear that will improve footing on slippery surfaces.

Handle fuel with care; it is highly flammable.

Use an approved fuel container.

Never add fuel to a running engine or hot engine.

Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

Replace gasoline cap securely and clean up spilled fuel before restarting.

Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

Never attempt to make any adjustments while the engine (motor) is running (except where specifically recommended by manufacturer).

OPERATION

Do not put hands or feet near or under rotating parts.

Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, thoroughly inspect the tiller for any damage, and repair the damage before restarting and operating the tiller.

Exercise caution to avoid slipping or falling.

If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

Stop the engine (motor) when leaving the operating position.

Take all possible precautions when leaving the machine unattended. Disengage the tines, shift into neutral, and stop the engine.

Keep children and pets away.

Do not overload the machine capacity by attempting to till too deep at too fast a rate.

Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing.

Never allow bystanders near the unit.

Use only attachments and accessories approved by the manufacturer of the tiller.

Never operate the tiller without good visibility or light.

Be careful when tilling in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.

MAINTENANCE AND STORAGE

Keep machine, attachments, and accessories in safe working condition.

Check shear pins, engine mounting bolts, and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow the engine to cool before storing in any enclosure.

Always refer to the operator’s guide instructions for important details if the tiller is to be stored for an ex- tended period.

- IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF ATTRACTING ATTENTION TO IMPORTANT OR CRITICAL INFORMATION IN THIS MANUAL.

IMPORTANT: USED TO ALERT YOU THAT THERE IS A POSSIBILITY OF DAMAGING THIS EQUIPMENT.

NOTE: Gives essential information that will aid you to better understand, incorporate, or execute a particular set of instructions.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

CAUTION: Always disconnect spark plug wire and place wire where it can- not contact spark plug in order to pre- vent accidental starting when setting up, transporting, adjusting or making repairs.

Before cleaning, repairing, or inspecting, shut off the engine and make certain all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting.Disconnect the cord on electric motors.

Do not run the engine indoors; exhaust fumes are dangerous.

Never operate the tiller without proper guards, plates, or other safety protective devices in place.

WARNING

The engine exhaust from this product con- tains chemicals known to the State of Cali- fornia to cause cancer, birth defects, or other reproductive harm.

2

Image 2
Contents Model NO. MRT500 Training Safety RulesMaintenance and Storage PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation Forward Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedTo Transport Before Starting EngineTurning ADD GasolineTilling Hints Tine Shear PinsTo Start Engine See Fig Adjust Wheels for Cultivating See Figs CultivatingGeneral Recommendations MaintenanceMaintenance Schedule Engine AIR Filter See FigSpark Plug CleaningMuffler Cooling System See FigTiller Service and AdjustmentsTo Adjust Handle Height See Fig Tire CareTine Replacement See Figs , 25 To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTo Remove Belt Guard See Fig To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Handle Assembly Tiller - Model Number MRT500 MXR500QMAINFRAME, Left Side MAINFRAME, Right Side KEY Part NO. NO. Description Tine Shield Tine Assembly Decals Limited Warranty

MRT500 specifications

The Poulan MRT500 is a versatile and powerful addition to the Poulan line of outdoor equipment, designed to meet the diverse needs of homeowners and landscaping professionals alike. This robust machine is primarily engineered for those tackling tougher yard tasks, such as tilling, cultivating, and preparing garden beds for planting.

At the heart of the MRT500 is a reliable engine that delivers outstanding performance. Featuring a 500cc four-stroke engine, it provides ample power for various gardening applications. This engine is designed for fuel efficiency, ensuring longer runtimes and reduced emissions while maintaining high torque levels needed for breaking up tough soil. The MRT500 also incorporates an easy-start mechanism, allowing users to get to work without the frustration of cumbersome starting procedures.

One of the standout characteristics of the MRT500 is its adjustable tilling width, which can be modified to suit different gardening needs. This flexibility allows users to till narrow rows for small gardens or wider paths for larger landscapes, making it an excellent choice for both casual gardeners and serious landscapers. The tilling depth can also be adjusted, ensuring maximum soil aeration and preparation, which is crucial for successful planting.

The machine is equipped with durable and robust tines that are designed to penetrate a variety of soil types, enabling effective tilling whether in clay, sandy, or loamy conditions. The tines can withstand the rigors of heavy use, ensuring longevity and performance consistency throughout the season.

In terms of user comfort, the MRT500 features ergonomic handles that are adjustable for height, making it suitable for users of varying stature. This focus on user experience reduces strain during operation, which is especially beneficial during extended work sessions. The lightweight design of the machine also allows for easy maneuverability, making it practical for both tight spaces and larger areas.

Additional features include a compact design for easy storage and transportation, as well as a straightforward assembly process, allowing users to set up the MRT500 quickly. With its combination of power, versatility, and user-friendly design, the Poulan MRT500 is an invaluable tool for any landscaping enthusiast or professional, ready to tackle a range of gardening projects with ease and efficiency. Whether preparing a new garden or maintaining an existing one, this tiller is sure to impress with its performance and reliability.