Poulan HDF825 manual HOW to USE Your Tiller, Stopping See Fig, Tine Operation See Fig, Tilling

Page 7

OPERATION

The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses.

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and oil or attempting to start engine.

STOPPING (See Fig. 5)

TINES

•Release forward tine control to stop forward move- ment.

•Release reverse tine control to stop reverse move- ment.

ENGINE

•Move throttle control to “STOP” position.

•Never use choke to stop engine.

					FORWARD TINE CONTROL IN
				REVERSE	“OFF” (UP) POSITION
				REVERSE
				CONTROL
					FORWARD TINE CONTROL
					IN “ON” (DOWN) POSITION
		_	9	4
	s		9
ndle


ha
					THROTTLE
					CONTROL
CHOKE
CONTROL
				e
				ngine_
				art
				_71

FIG. 5

TINE OPERATION (See Fig. 5)

FORWARD

•Squeeze forward tine control to handle.

REVERSE

•With forward tine control “OFF” (up) position, pull back and hold reverse tine control.

TILLING

The speed and depth of tilling is regulated by the position of the depth stake and wheel height.

The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller’s forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig.

DEPTH STAKE (See Fig. 6)

Adjust depth stake by removing the hairpin clip and clevis pin. Change depth stake to desired position. Replace the clevis pin and hairpin clip.

•For normal tilling, set depth stake at the second or third hole from the top.

WHEELS (See Fig. 6)

Adjust wheels by removing the hairpin clip and clevis pin. Change wheel position. Replace the hairpin clip and clevis pin.

•For normal tilling, set wheels at the second or third hole from the top.

depth_	HAIRPIN CLIP
depth_	AND CLEVIS PIN
stake
_
4
	DEPTH
	STAKE
	STAKE
	SPRING
	WHEEL

FIG. 6

7

Image 7

Contents Always Wear EYE Protection During Operation Operators Manual ModelPreparation Safety RulesMaintenance and Storage TrainingTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthOperation Meets Ansi Safety RequirementsKnow Your Tiller Tilling HOW to USE Your TillerStopping See Fig Tine Operation See FigADD Gasoline Before Starting EngineTo Transport Fill Engine with OIL See FigTilling Hints Breaking in Your TillerCultivating Maintenance Schedule MaintenanceGeneral Recommendations To Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See FigCleaning Service and AdjustmentsTiller Final Check OFF Position Tine Operation Check See FigTo Remove Belt Guard See Fig To Replace V-BELTS See FigsCheck Tine Operation To Adjust CarburetorBelt Replacement Belt RemovalEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Bouché dessence Réservoir Dépannage DE GuideMotobineuse EntreposageSupplementaire Information Moteur21 .FIG Réglages ET RévisionCarburateur LE Régler Pour 15 22 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Guidon DU Hauteur LA Régler Pour Fig la Voir Sesfrai DES L’UTILISATION DE VérificationFraises DES Disposition 15 .FIG Fig la VoirSilencieux EntretienNettoyage ’ALLUMAGE BougieFig la Voir AIR À Filtre MoteurLubrification Lubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN CalendrierLabourage DE Conseils UtilisationMotobineuse LA DE Rodage Culture’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantGﬁ la Voir Moteur LE Démarrer PourFig la FRAISESVoir DES Utilisation BineuseMoto Votre Utiliser Comment LabourageMotobineuse Votre Motobineuse Votre ConnaissezMoteur le démarrer de permet Démarrage DE Poignée Geraboula DU Largeur Manche LE Installer ET DéballerMontage Dents DES UtilisationDe Clés 2 Pince 1 Tournevis 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESRéglages ET Révision Client DU Responsabilités SommaireProduit DU Spécifications Client DU ResponsabilitésEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité touteDU Manuel OpérateurAvertissement