Poulan HDF825 AIR Cleaner See Fig, Cooling System See Fig, To Change Engine OIL See Figs

Page 11

MAINTENANCE

Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine.

Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.

Do not touch hot muffler or cylinder fins as contact may cause burns.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classifi cation SG-SL. Select the oil’s SAE viscosity grade according to your expected temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart1_e

FIG. 11

NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.) improve starting in cold weather, these multi viscosity oils will result in increased oil consumption when used above 32°F (0°C). Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the tiller is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each fi ve (5) hours of continuous use. Add SAE 30 motor oil or equivalent. Tighten oil fi ller plug securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expected before oil change. All oil must meet API service classifi cation SG-SL.

Be sure tiller is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove drain plug.

Tip tiller forward to drain oil.

After oil has drained completely, replace oil drain plug and tighten securely.

Remove oil fi ller plug. Be careful not to allow dirt to enter the engine.

Refill engine with oil. See “CHECK ENGINE OILLEVEL” in the Operation section of this manual.

engine_art_12

OIL

DRAIN

PLUG

OIL LEVEL

OIL FILLER

PLUG

FIG. 12

AIR CLEANER (See Fig. 13)

Service air cleaner cartridge every twenty-fi ve hours, more often if engine is used in very dusty conditions.

Loosen air cleaner screws, one on each side of cover.

Remove air cleaner cover.

Carefully remove air cleaner cartridge. Be careful. Do not allow dirt or debris to fall into carburetor.

Clean by tapping gently on a fl at surface.

If very dirty or damaged, replace cartridge.

Clean and replace cover. Tighten screws securely.

CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge.

AIR CLEANER CARTRIDGE

COVER

AIR

CLEANER

SCREW

FIG. 13

COOLING SYSTEM (See Fig. 14)

Your engine is air cooled. For proper engine performance and long life keep your engine clean.

Clean air screen frequently using a stiff-bristled- brush.

Remove blower housing and clean as necessary.

Keep cylinder fi ns free of dirt and chaff.

CYLINDER FINS

MUFFLER

BLOWER

HOUSING

AIR

SCREEN

engine_art_71

FIG. 14

11

Image 11
Contents Always Wear EYE Protection During Operation Operators Manual ModelPreparation Safety RulesMaintenance and Storage TrainingTable of Contents Contents of Hardware Pack AssemblyTools Required for Assembly Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthKnow Your Tiller Meets Ansi Safety RequirementsOperation Tilling HOW to USE Your TillerStopping See Fig Tine Operation See Fig ADD Gasoline Before Starting Engine To Transport Fill Engine with OIL See FigCultivating Breaking in Your TillerTilling Hints General Recommendations MaintenanceMaintenance Schedule To Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See FigTiller Service and AdjustmentsCleaning Final Check OFF Position Tine Operation Check See FigTo Remove Belt Guard See Fig To Replace V-BELTS See FigsCheck Tine Operation To Adjust CarburetorBelt Replacement Belt RemovalEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Bouché dessence Réservoir Dépannage DE GuideMotobineuse EntreposageSupplementaire Information Moteur21 .FIG Réglages ET RévisionCarburateur LE Régler Pour 15 22 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Guidon DU Hauteur LA Régler Pour Fig la Voir Sesfrai DES L’UTILISATION DE VérificationFraises DES Disposition 15 .FIG Fig la VoirSilencieux EntretienNettoyage ’ALLUMAGE BougieLubrification MoteurFig la Voir AIR À Filtre Lubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN CalendrierLabourage DE Conseils UtilisationMotobineuse LA DE Rodage Culture’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantGfi la Voir Moteur LE Démarrer PourFig la FRAISESVoir DES Utilisation BineuseMoto Votre Utiliser Comment LabourageMoteur le démarrer de permet Démarrage DE Poignée Motobineuse Votre ConnaissezMotobineuse Votre Geraboula DU Largeur Manche LE Installer ET DéballerMontage Dents DES UtilisationDe Clés 2 Pince 1 Tournevis 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESRéglages ET Révision Client DU Responsabilités SommaireProduit DU Spécifications Client DU ResponsabilitésEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité touteAvertissement OpérateurDU Manuel