Poulan PRRT875X manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 18

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

CAUTION: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

•Clean entire tiller (See “CLEANING” in the Maintenance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent.

•Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stablizer container. Run engine at least 10 minutes after adding stablizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug.

•Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

•Pull starter handle slowly several times to distribute oil.

•Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your unit indoors and cover it to give protection from dust and dirt.

•Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PRRT875X Training Safety RulesMaintenance and Storage PreparationTable of Contents Contents of Hardware Pack AssemblyTools Required for Assembly OPERATOR’S Position See FigInstall Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller To Transport Before Starting EngineADD Gasoline Tine Shear Pins Tilling HintsCultivating Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsAIR Cleaner See Fig EngineTo Change Engine OIL See Figs Muffler CleaningCooling System See Fig Spark PlugService and Adjustments TillerTire Care Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Service Notes Limited Warranty HOPParts and Service Changere DE Pièces LES ET L’ENTRETIEN Limitée Garantie Dépannage DE Guide Moteur EntreposageSupplementaire Information MotobineuseCarburateur LE Régler Pour Réglages ET RévisionMoteur 27 .FIG26 et 25 26 .FIG25 .FIG 24 .FIG Courroie LA Remplacer Pour Fig la Voir Terre À D’ENTRAÎNEMENT Courroie LA Régler23 et 22 .fig les Voir Terre À D’ENTRAÎNEMENTDE Protecteur LE Enlever Pour Fig la Voir Roue LA Enlever PourFig la Voir Roiecour Fig la Voir’ALLUMAGE Bougie EntretienNettoyage SilencieuxFig la Voir AIR À Filtre Lubrification’ENTRETIEN Calendrier Générales RecommandationsLubrification DE Tableau LubrificationDents DES Cisaillement DE Boulons UtilisationBinage 15 .FIG14 .FIG Labourage DE ConseilsMoteur LE Démarrer Pour 13 .FIG’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantExtérieurs Latéraux Déflecteurs Transporter PourMENT/LESLESEU ROUES-AVANT Marche BineuseMoto Votre Utiliser Comment LA Avec -FRAISES DES UtilisationAnsi Sécurité DE Exigences AUX Conforme Motobineuse Votre ConnaissezMontage Fig la Voir SetesviPoignee LA Installer Et 4, 3, .fig les VoirFig la Voir Carton LE Deballer Pièces DES SAC DU Contenu Fig la Voir D’OPERATEUR PositionMontage LE Pour Exiges Outils LES Sommaire Client DU ResponsabilitésProduit DE Spécifications Motobineuses des Sécurité toute Sécurité DE RèglesEntreposage ET Entretien En lUtilisation pour ConseilsCom.pro-poulan.www web site notre Visitez

PRRT875X specifications

The Poulan PRRT875X is a robust and versatile string trimmer designed for both residential and professional landscaping tasks. Known for its lightweight design and powerful performance, this tool caters to individuals looking to maintain their lawns with precision and ease.

One of the standout features of the PRRT875X is its impressive 25cc, 2-cycle gas engine. This enables the trimmer to deliver a strong performance, allowing users to tackle thick grass, weeds, and overgrown areas without hassle. The engine is designed for easy starting, which reduces the frustration often associated with traditional gas-powered trimmers.

The PRRT875X is equipped with a 18-inch cutting swath, providing ample coverage with each pass. This wide cutting width not only saves time but also enhances efficiency, making it easier to trim larger areas quickly. The dual-line design enables a cleaner cut, distributing power evenly across both lines, resulting in improved performance.

Comfort and usability are key considerations in the design of the Poulan PRRT875X. It features an adjustable handle that allows users to customize the grip for better control and comfort during extended use. The curved shaft design also contributes to ease of operation, reducing strain on the user's back and arms while trimming hard-to-reach areas.

The trimmer also employs a 'Tap-N-Go' line advance system. This technology enables users to easily feed more line by simply tapping the head on the ground, minimizing downtime and enhancing overall productivity. Moreover, the cutting head is designed for quick line replacement, which is a significant advantage for users who require frequent blade changes.

Durability is paramount in the design of the PRRT875X. It features a rugged exterior designed to withstand the rigors of outdoor use. Additionally, its lightweight build, weighing approximately 10 lbs, allows for easy maneuverability and transport.

In terms of environmental considerations, the Poulan PRRT875X meets various emissions standards, making it a greener option in the gas-powered trimmer market.

Overall, the Poulan PRRT875X string trimmer combines power, efficiency, and user-friendly features, making it an excellent choice for anyone looking to maintain their landscape effectively. With its robust engine, wide cutting swath, and focus on comfort, it stands out as a reliable tool for homeowners and professionals alike.
Top Page Image Contents