Poulan PRRT875X manual Safety Rules, Training, Preparation, Operation, Maintenance and Storage

Page 2

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Rotary Tillers

TRAINING

Read the Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

Keep the area of operation clear of all persons, par- ticularly small children, and pets.

Never operate the tiller without proper guards, plates, or other safety protective devices in place.

Keep children and pets away.

Do not overload the machine capacity by attempting to till too deep at too fast a rate.

Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing.

Never allow bystanders near the unit.

Use only attachments and accessories approved by the manufacturer of the tiller.

PREPARATION

Thoroughly inspect the area where the equipment is to be used and remove all foreign objects.

Disengage all clutches and shift into neutral before starting the engine (motor).

Never operate the tiller without good visibility or light.

Be careful when tilling in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.

Do not operate the equipment without wearing ade- quate outer garments. Wear footwear that will improve footing on slippery surfaces.

Handle fuel with care; it is highly flammable.

Use an approved fuel container.

Never add fuel to a running engine or hot engine.

Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

Replace gasoline cap securely and clean up spilled fuel before restarting.

Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

Never attempt to make any adjustments while the engine (motor) is running (except where specifically recommended by manufacturer).

OPERATION

Do not put hands or feet near or under rotating parts.

Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, thoroughly inspect the tiller for any damage, and repair the damage before restarting and operating the tiller.

Exercise caution to avoid slipping or falling.

If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

Stop the engine (motor) when leaving the operating position.

Take all possible precautions when leaving the machine unattended. Disengage the tines, shift into neutral, and stop the engine.

Before cleaning, repairing, or inspecting, shut off the engine and make certain all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting. Disconnect the cord on electric motors.

Do not run the engine indoors; exhaust fumes are dangerous.

2

MAINTENANCE AND STORAGE

Keep machine, attachments, and accessories in safe working condition.

Check shear pins, engine mounting bolts, and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow the engine to cool before storing in any enclosure.

Always refer to the operator’s guide instructions for important details if the tiller is to be stored for an ex- tended period.

- IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF ATTRACTING ATTENTION TO IMPORTANT OR CRITICAL INFORMATION IN THIS MANUAL.

IMPORTANT: USED TO ALERT YOU THAT THERE IS A POSSIBILITY OF DAMAGING THIS EQUIPMENT.

NOTE: Gives essential information that will aid you to better understand, incorporate, or execute a particular set of instructions.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

CAUTION: Always disconnect spark plug wire and place wire where it can- not contact spark plug in order to pre- vent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproduc- tive harm.

Image 2
Contents PRRT875X Training Safety RulesMaintenance and Storage PreparationTable of Contents Contents of Hardware Pack AssemblyTools Required for Assembly OPERATOR’S Position See FigInstall Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation HOW to USE Your Tiller ADD Gasoline To TransportBefore Starting Engine Cultivating Tine Shear PinsTilling Hints Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsTo Change Engine OIL See Figs AIR Cleaner See FigEngine Muffler CleaningCooling System See Fig Spark PlugTire Care Service and AdjustmentsTiller Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Service Notes Limited Warranty HOPParts and Service Changere DE Pièces LES ET L’ENTRETIEN Limitée Garantie Dépannage DE Guide Moteur EntreposageSupplementaire Information MotobineuseCarburateur LE Régler Pour Réglages ET RévisionMoteur 27 .FIG25 .FIG 24 .FIG 26 et 2526 .FIG Courroie LA Remplacer Pour Fig la Voir Terre À D’ENTRAÎNEMENT Courroie LA Régler23 et 22 .fig les Voir Terre À D’ENTRAÎNEMENTDE Protecteur LE Enlever Pour Fig la Voir Roue LA Enlever PourFig la Voir Roiecour Fig la Voir’ALLUMAGE Bougie EntretienNettoyage SilencieuxFig la Voir AIR À Filtre Lubrification’ENTRETIEN Calendrier Générales RecommandationsLubrification DE Tableau LubrificationDents DES Cisaillement DE Boulons UtilisationBinage 15 .FIG14 .FIG Labourage DE ConseilsMoteur LE Démarrer Pour 13 .FIG’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantExtérieurs Latéraux Déflecteurs Transporter PourMENT/LESLESEU ROUES-AVANT Marche BineuseMoto Votre Utiliser Comment LA Avec -FRAISES DES UtilisationAnsi Sécurité DE Exigences AUX Conforme Motobineuse Votre ConnaissezMontage Fig la Voir SetesviFig la Voir Carton LE Deballer Poignee LA InstallerEt 4, 3, .fig les Voir Montage LE Pour Exiges Outils LES Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Produit DE Spécifications SommaireClient DU Responsabilités Motobineuses des Sécurité toute Sécurité DE RèglesEntreposage ET Entretien En lUtilisation pour ConseilsCom.pro-poulan.www web site notre Visitez

PRRT875X specifications

The Poulan PRRT875X is a robust and versatile string trimmer designed for both residential and professional landscaping tasks. Known for its lightweight design and powerful performance, this tool caters to individuals looking to maintain their lawns with precision and ease.

One of the standout features of the PRRT875X is its impressive 25cc, 2-cycle gas engine. This enables the trimmer to deliver a strong performance, allowing users to tackle thick grass, weeds, and overgrown areas without hassle. The engine is designed for easy starting, which reduces the frustration often associated with traditional gas-powered trimmers.

The PRRT875X is equipped with a 18-inch cutting swath, providing ample coverage with each pass. This wide cutting width not only saves time but also enhances efficiency, making it easier to trim larger areas quickly. The dual-line design enables a cleaner cut, distributing power evenly across both lines, resulting in improved performance.

Comfort and usability are key considerations in the design of the Poulan PRRT875X. It features an adjustable handle that allows users to customize the grip for better control and comfort during extended use. The curved shaft design also contributes to ease of operation, reducing strain on the user's back and arms while trimming hard-to-reach areas.

The trimmer also employs a 'Tap-N-Go' line advance system. This technology enables users to easily feed more line by simply tapping the head on the ground, minimizing downtime and enhancing overall productivity. Moreover, the cutting head is designed for quick line replacement, which is a significant advantage for users who require frequent blade changes.

Durability is paramount in the design of the PRRT875X. It features a rugged exterior designed to withstand the rigors of outdoor use. Additionally, its lightweight build, weighing approximately 10 lbs, allows for easy maneuverability and transport.

In terms of environmental considerations, the Poulan PRRT875X meets various emissions standards, making it a greener option in the gas-powered trimmer market.

Overall, the Poulan PRRT875X string trimmer combines power, efficiency, and user-friendly features, making it an excellent choice for anyone looking to maintain their landscape effectively. With its robust engine, wide cutting swath, and focus on comfort, it stands out as a reliable tool for homeowners and professionals alike.