Troy-Bilt 645A-Bronco manual Introduction, Initial Operation, Starting and Stopping the Engine

Page 13

Section

4Operation

WARNING

Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section

4)in this Manual, in the separate Engine Owner’s Manual, and on the decals on the machine.

Failure to follow these instruc- tions can result in serious personal injury.

INTRODUCTION

 

Reverse Clutch Control

 

(knob on back of bracket)

 

Forward Clutch Bail

 

Depth Regulator Lever

 

Anti-Reverse Stake

Recoil Starter

Wheel Drive Pin

 

(on each wheel)

Figure 4-1

 

Read this Section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden. Find an open, level area and practice using the tiller controls without the tines engaging the soil (put tines in “travel” setting). Only after you’ve become completely familiar with the tiller should you begin using it in the garden.

INITIAL OPERATION

Perform the following maintenance during the first hours of new operation (see “Maintenance” section in this manual and in the Engine Owner’s Manual).

1.Change engine oil after first 2 hours of new engine operation.

2.Check for loose or missing hardware on unit. Tighten or replace as needed.

3.Check tension on forward drive belt after first 2 hours of operation.

4.Check transmission gear oil level after first 2 hours of operation.

STARTING AND STOPPING THE ENGINE

Pre-Start Checklist

Make the following checks and perform the following services before starting the engine.

1.Read the “Safety” and “Controls” sections in this manual. Read the separate Engine Owner’s Manual provided by the engine manufacturer.

2.Check that the wheels are in the WHEEL DRIVE position (wheel pins must be through the wheel hubs and the wheel shaft holes).

3.Check unit for loose or missing hardware. Service as required.

4.Check engine oil level. See Engine Owner’s Manual.

5.Check that all safety guards and covers are in place.

6.Check air cleaner and engine cooling system. See Engine Owner’s Manual.

7.Attach spark plug wire to spark plug.

8.Fill the fuel tank with gasoline according to the directions in the separate Engine Owner’s Manual. Follow all instructions and safety rules carefully.

DANGER

GASOLINE IS HIGHLY FLAMMABLE AND ITS VAPORS ARE EXPLOSIVE.

Follow gasoline safety rules in this manual (see Section 1) and in the separate Engine Owner’s Manual.

Failure to follow gasoline safety instructions can result in serious personal injury and property damage.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Finding Model Number Table of ContentsEngine Information Calling Customer SupportTraining SafetyKeep children and pets away Use a deep depth regulator setting Use slower engine speedsNever operate the tiller under Decals Operating SymbolsTools/Materials Needed for Assembly AssemblyLoose Parts List Qty. Description IntroductionMove Tiller Off Shipping Platform Attach HandlebarInstall Reverse Clutch Cable Install Forward Clutch CableCheck Hardware for Tightness Check Level Transmission Gear OilCheck Air Pressure in Tires Tiller is shipped without oil in the engineWheel Drive Pins Features and ControlsReverse Clutch Control Forward Clutch BailTo Operate the Forward Clutch Bail To Operate the Reverse Clutch ControlShallow Settings Deep Handlebar Height AdjustmentTo Adjust the Handlebars Depth Regulator LeverIntroduction OperationInitial Operation Starting and Stopping the EngineOperating the Tiller Use the Fast throttle speed setting when tillingStarting the Engine Stopping the Engine and TillerFor reverse motion of the wheels and tines Turning the Tiller AroundStopping the Tiller and Engine Tilling depths Let the tiller do the workAvoid tilling soggy, wet soil Avoid making footprintsClearing the tines Tilling across slopes without using terracesTilling on slopes Tilling up and down slopesLoading and Unloading the Tiller Required Maintenance Schedule MaintenanceEvery HoursTiller Lubrication Transmission Gear OIL ServiceCheck for OIL Leaks Check HardwareRemoving and Installing Individual Tines Removing and Installing Tine AssembliesTines Tine InspectionTo Check Forward Belt Tension PositionReverse Belt Replacement Information Forward Clutch Bail AdjustmentTo Check Reverse Belt Tension AIR Cleaner Service Engine OIL ServiceSpark Plug Service Engine CleaningTroubleshooting Parts List Models 644H & 645A Models 644H & 645A Models 644H & 645A GW-1224-3 Front 619-04013 RIGHT-HAND Tine 2926 Models 644H & 645A TROY-BILT LLC, P.O. Box 361131, Cleveland, Ohio 44136-0019 TROY-BILT Tiller Lifetime Limited Warranty
Top Page Image Contents