Poulan 401423, 96092000500 manual ADD Gasoline, To Start Engine See Fig, Tilling Hints See Fig

Page 10

OPERATION

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Fill to within 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is ac- cidentally spilled, move machine away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.

Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 14)

CAUTION: Keep drive control bar in “DISENGAGED” position when start- ing engine.

When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine.

Make sure spark plug wire is properly connected.

Move shift lever indicator to “N” (neutral) position.

Place throttle control in “FAST” position.

Turn fuel shut-off valve 1/4 turn to open position.

Move choke control to choke position.

Grasp recoil starter handle with one hand and grasp tiller handle with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point).

Pull recoil starter handle quickly. Do not let starter handle snap back against starter.

If engine fires but does not start, move choke control to half choke position. Pull recoil starter handle until engine starts.

When engine starts, slowly move choke control to "RUN" position as engine warms up.

NOTE: A warm engine requires less choking to start.

Move throttle control to desired running position.

Allow engine to warm up for a few minutes before engaging tines.

NOTE: If at a high altitude (3000 feet) or in cold temperatures (below 32°F), the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual.

NOTE: If engine does not start, see troubleshooting points.

CHOKE CONTROL

RUN

CHOKE

RECOIL STARTER

HANDLE

FIG. 14

TILLING HINTS (See Fig. 15)

CAUTION: Until you are accustomed to handling your tiller,start actual field use with throttle in slow position (mid-way between “FAST” and “IDLE”).

Tilling is digging into, turning over, and breaking up packed soil before planting.Loose, unpacked soil helps root growth. Best tilling depth is 4" to 6" (10-15 cm). A tiller will also clear the soil of unwanted vegetation. The decomposition of this vegetable matter enriches the soil. Depending on the climate (rainfall and wind), it may be advisable to till the soil at the end of the growing season to further condition the soil.

You will find tilling much easier if you leave a row un- tilled between passes. Then go back between tilled rows. (See Fig. 14) There are two reasons for doing this. First, wide turns are much easier to negotiate than about-faces. Second, the tiller won’t be pulling itself, and you, toward the row next to it.

Soil conditions are important for proper tilling.Tines will not readily penetrate dry, hard soil which may contribute to excessive bounce and difficult handling of your tiller. Hard soil should be moistened before tilling; however, extremely wet soil will “ball-up” or clump during tilling. Wait until the soil is less wet in order to achieve the best results. When tilling in the fall, remove vines and long grass to prevent them from wrapping around the

tine shaft and slowing your tilling operation.

10

Image 10
Contents DRT65 Always Wear EYE Protection During OperationTraining Safety RulesMaintenance and Storage PreparationTable of Contents Tools Required for Assembly AssemblyOPERATOR’S Position See Fig Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureOperation Meets Ansi Safety RequirementsKnow Your Tiller Forward Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedTo Transport TurningCultivating Before Starting EngineTo Start Engine See Fig ADD GasolineTilling Hints See Fig Adjust Wheels for Cultivating See Figs Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsEngine AIR Filter See FigMuffler CleaningCooling System See Fig Spark PlugTiller Service and AdjustmentsTire Care Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 28 To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Limited Warranty Parts and Service

96092000500, 401423 specifications

The Poulan 401423, also known by its part number 96092000500, is a versatile and reliable outdoor power equipment designed to meet the needs of homeowners and gardening enthusiasts alike. This model is particularly well-regarded for its rugged construction, powerful performance, and user-friendly features, making it an ideal choice for various lawn care tasks.

One of the standout characteristics of the Poulan 401423 is its robust engine. It features a potent 40cc 2-cycle engine, providing ample power for cutting through thick grass, weeds, and brush. This engine design not only delivers impressive torque but also ensures a lightweight feel, allowing users to maneuver the equipment with ease. The engine is paired with a high-efficiency air filter that enhances performance and extends the equipment's lifespan by minimizing dust and debris intake.

In addition to its powerful engine, the Poulan 401423 features an adjustable cutting head that allows users to customize their cutting height based on the type of terrain and the desired lawn appearance. This feature is particularly beneficial for maintaining a pristine lawn, as it enables precise control over the grass length. The cutting head is also designed with a dual-line system that provides efficient trimming, helping to achieve a clean edge along sidewalks and flower beds.

Ergonomics is another key focus in the design of the Poulan 401423. The equipment is equipped with a comfortable, padded handle that reduces user fatigue, making it ideal for extended use. Additionally, it has a lightweight structure, which minimizes strain on the arms and back while working on landscaping projects.

Technology-wise, the Poulan 401423 incorporates anti-vibration technology, which significantly reduces vibrations felt by the user. This not only enhances comfort but also improves accuracy during operation, ensuring a more enjoyable lawn care experience.

Furthermore, the model features an easy-start mechanism, which allows for quick ignition with minimal effort. This is particularly useful for users who may struggle with traditional starting methods, ensuring that the equipment is ready to go when you are.

Overall, the Poulan 401423,96092000500 stands out as a powerful and efficient tool for outdoor maintenance. With its robust engine, adjustable cutting capabilities, ergonomic design, and innovative technology, it embodies the qualities that make it a top choice for anyone serious about lawn care. Whether tackling overgrown areas or fine-tuning the edges of your garden, this model successfully delivers on performance and user satisfaction.