Poulan 401423 manual Safety Rules, Training, Preparation, Operation, Maintenance and Storage

Page 2

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Rotary Tillers

TRAINING

•Read the Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

•Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

•Keep the area of operation clear of all persons, par- ticularly small children, and pets.

PREPARATION

•Thoroughly inspect the area where the equipment is to be used and remove all foreign objects.

•Disengage all clutches and shift into neutral before starting the engine (motor).

•Never operate the tiller without proper guards, plates, or other safety protective devices in place.

•Keep children and pets away.

•Do not overload the machine capacity by attempting to till too deep at too fast a rate.

•Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing.

•Never allow bystanders near the unit.

•Use only attachments and accessories approved by the manufacturer of the tiller.

•Never operate the tiller without good visibility or light.

•Be careful when tilling in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine.

•Do not operate the equipment without wearing ade- quate outer garments. Wear footwear that will improve footing on slippery surfaces.

•Handle fuel with care; it is highly flammable.

•Use an approved fuel container.

•Never add fuel to a running engine or hot engine.

•Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

•Replace gasoline cap securely and clean up spilled fuel before restarting.

•Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

•Never attempt to make any adjustments while the engine (motor) is running (except where specifically recommended by manufacturer).

OPERATION

•Do not put hands or feet near or under rotating parts.

•Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

•After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, thoroughly inspect the tiller for any damage, and repair the damage before restarting and operating the tiller.

•Exercise caution to avoid slipping or falling.

•If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

•Stop the engine (motor) when leaving the operating position.

•Take all possible precautions when leaving the machine unattended. Disengage the tines, shift into neutral, and stop the engine.

•Before cleaning, repairing, or inspecting, shut off the engine and make certain all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting.Disconnect the cord on electric motors.

•Do not run the engine indoors; exhaust fumes are dangerous.

MAINTENANCE AND STORAGE

•Keep machine, attachments, and accessories in safe working condition.

•Check shear pins, engine mounting bolts, and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

•Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow the engine to cool before storing in any enclosure.

•Always refer to the operator’s guide instructions for important details if the tiller is to be stored for an ex- tended period.

- IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF ATTRACTING ATTENTION TO IMPORTANT OR CRITICAL INFORMATION IN THIS MANUAL.

IMPORTANT: USED TO ALERT YOU THAT THERE IS A POSSIBILITY OF DAMAGING THIS EQUIPMENT.

NOTE: Gives essential information that will aid you to better understand, incorporate, or execute a particular set of instructions.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

CAUTION: Always disconnect spark plug wire and place wire where it can- not contact spark plug in order to pre- vent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproduc- tive harm.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents DRT65 Always Wear EYE Protection During OperationTraining Safety RulesMaintenance and Storage PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation Forward Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedTo Transport TurningCultivating Before Starting EngineTilling Hints See Fig ADD GasolineTo Start Engine See Fig Adjust Wheels for Cultivating See Figs Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsEngine AIR Filter See FigMuffler CleaningCooling System See Fig Spark PlugTire Care Service and AdjustmentsTiller Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 28 To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Limited Warranty Parts and Service

96092000500, 401423 specifications

The Poulan 401423, also known by its part number 96092000500, is a versatile and reliable outdoor power equipment designed to meet the needs of homeowners and gardening enthusiasts alike. This model is particularly well-regarded for its rugged construction, powerful performance, and user-friendly features, making it an ideal choice for various lawn care tasks.

One of the standout characteristics of the Poulan 401423 is its robust engine. It features a potent 40cc 2-cycle engine, providing ample power for cutting through thick grass, weeds, and brush. This engine design not only delivers impressive torque but also ensures a lightweight feel, allowing users to maneuver the equipment with ease. The engine is paired with a high-efficiency air filter that enhances performance and extends the equipment's lifespan by minimizing dust and debris intake.

In addition to its powerful engine, the Poulan 401423 features an adjustable cutting head that allows users to customize their cutting height based on the type of terrain and the desired lawn appearance. This feature is particularly beneficial for maintaining a pristine lawn, as it enables precise control over the grass length. The cutting head is also designed with a dual-line system that provides efficient trimming, helping to achieve a clean edge along sidewalks and flower beds.

Ergonomics is another key focus in the design of the Poulan 401423. The equipment is equipped with a comfortable, padded handle that reduces user fatigue, making it ideal for extended use. Additionally, it has a lightweight structure, which minimizes strain on the arms and back while working on landscaping projects.

Technology-wise, the Poulan 401423 incorporates anti-vibration technology, which significantly reduces vibrations felt by the user. This not only enhances comfort but also improves accuracy during operation, ensuring a more enjoyable lawn care experience.

Furthermore, the model features an easy-start mechanism, which allows for quick ignition with minimal effort. This is particularly useful for users who may struggle with traditional starting methods, ensuring that the equipment is ready to go when you are.

Overall, the Poulan 401423,96092000500 stands out as a powerful and efficient tool for outdoor maintenance. With its robust engine, adjustable cutting capabilities, ergonomic design, and innovative technology, it embodies the qualities that make it a top choice for anyone serious about lawn care. Whether tackling overgrown areas or fine-tuning the edges of your garden, this model successfully delivers on performance and user satisfaction.
Top Page Image Contents