Poulan 401423, 96092000500 manual Troubleshooting Points

Page 20

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Dirty air cleaner.

4.

Clean or replace air cleaner cartridge.

 

5.

Water in fuel.

5.

Empty fuel tank and carburetor, and refill tank

 

 

 

 

with fresh gasoline.

 

6.

Clogged fuel tank.

6.

Remove fuel tank and clean.

 

7.

Loose spark plug wire.

7.

Make sure spark plug wire is seated properly on

 

 

 

 

plug.

 

8.

Bad spark plug or improper gap.

8.

Replace spark plug or adjust gap.

 

9.

Carburetor out of adjustment.

9.

Make necessary adjustments.

 

 

 

 

 

Hard to start

1.

Throttle control not set properly.

1.

Place throttle control in “FAST” position.

 

2.

Dirty air cleaner.

2.

Clean or replace air cleaner cartridge.

 

3.

Bad spark plug or improper gap.

3.

Replace spark plug or adjust gap.

 

4.

Stale or dirty fuel.

4.

Empty fuel tank and refill tank with fresh, clean

 

 

 

 

gasoline.

 

5.

Loose spark plug wire.

5.

Make sure spark plug wire is seated properly on

 

 

 

 

plug.

 

6.

Carburetor out of adjustment.

6.

Make necessary adjustments.

 

 

 

 

 

Loss of power

1.

Engine is overloaded.

1.

Set depth stake for shallower tilling.

 

2.

Dirty air cleaner.

2.

Clean or replace air cleaner cartridge.

 

3.

Low oil level/dirty oil.

3.

Check oil level/change oil.

 

4.

Faulty spark plug.

4.

Clean and regap or change spark plug.

 

5.

Oil in fuel.

5.

Empty and clean fuel tank and refill, and clean

 

 

 

 

carburetor.

 

6.

Stale or dirty fuel.

6.

Empty fuel tank and refill fuel tank with fresh

 

 

 

 

gasoline.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, and refill tank

 

 

 

 

with fresh gasoline.

 

8.

Clogged fuel tank.

8.

Remove fuel tank and clean.

 

9.

Spark plug wire loose.

9.

Connect and tighten spark plug wire.

 

10.

Dirty engine air screen.

10.

Clean engine air screen.

 

11.

Dirty/clogged muffler.

11.

Clean/replace muffler.

 

12.

Carburetor out of adjustment.

12.

Make necessary adjustments.

 

13.

Poor compression.

13.

Contact an authorized service centerdepartment.

 

 

 

 

 

Engine overheats

1.

Low oil level/dirty oil.

1.

Check oil level/change oil.

 

2.

Dirty engine air screen.

2.

Clean engine air screen.

 

3.

Dirty engine.

3.

Clean cylinder fins, air screen, and muffler area.

 

4.

Partially plugged muffler.

4.

Remove and clean muffler.

 

5.

Improper carburetor adjustment.

5.

Adjust carburetor to richer position.

 

 

 

 

 

Excessive bounce/

1.

Ground too dry and hard.

1.

Moisten ground or wait for more favorable soil

difficult handling

 

 

 

conditions.

 

 

 

 

 

Soil balls up or clumps

1.

Ground too wet.

1.

Wait for more favorable soil conditions.

 

 

 

 

 

Engine runs but tiller

1.

Drive control bar is not engaged.

1.

Engage drive control.

won’t move

2.

V-belt not correctly adjusted.

2.

Inspect/adjust V-belt.

 

3.

V-belt is off pulley(s).

3.

Inspect V-belt.

 

 

 

 

 

Engine runs but labors

1.

Tilling too deep.

1.

Set depth stake for shallower tilling.

when tilling

2.

Throttle control not properly adjusted.

2.

Check throttle control setting.

 

3.

Carburetor out of adjustment.

3.

Make necessary adjustments.

 

 

 

 

 

Tines will not rotate

1.

Shear pin(s) broken.

1.

Replace shear pin(s).

 

 

 

 

 

Tines skip over

1.

Drag Stake not lowered in forward rotating

1.

Lower Drag Stake

ground

 

till mode.

 

 

 

2.

Improper tilling mode.

2.

Forward rotating tine drive should only be used

 

 

 

 

for soft ground or for soil that has already been

 

 

 

 

tilled.

 

 

 

 

 

Hard to shift into gear

1.

Gears not timed.

1.

Briefly engage drive control bar and release or

 

 

 

 

rock tiller forward and backward until are able to

 

 

 

 

shift gears.

 

 

 

 

 

Tiller shuts off when

1.

Shift lever set in between counter rotating till

1.

Shift to either counter rotating till position or forward

drive control bar

 

position and forward rotating till position.

 

rotating till position.

engaged

2.

Tines jammed.

2.

Clear tines.

 

 

 

 

 

 

 

 

 

 

20

Image 20
Contents DRT65 Always Wear EYE Protection During OperationSafety Rules Maintenance and StorageTraining PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Install Handle See Figs , 4, Unpacking Carton See FigAttach Clutch Cable See Fig Connect Shift ROD See FigRemove Tiller from Crate Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation HOW to USE Your Tiller Tine Operation with Wheel DriveForward Wheels ONLY/TINES Stopped Reverse Wheels ONLY/TINES StoppedTurning CultivatingTo Transport Before Starting EngineTilling Hints See Fig ADD GasolineTo Start Engine See Fig Adjust Wheels for Cultivating See Figs Maintenance Maintenance ScheduleLubrication Chart General RecommendationsEngine AIR Filter See FigCleaning Cooling System See FigMuffler Spark PlugTire Care Service and AdjustmentsTiller Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 28 To Adjust Throttle Control Cable See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Limited Warranty Parts and Service

96092000500, 401423 specifications

The Poulan 401423, also known by its part number 96092000500, is a versatile and reliable outdoor power equipment designed to meet the needs of homeowners and gardening enthusiasts alike. This model is particularly well-regarded for its rugged construction, powerful performance, and user-friendly features, making it an ideal choice for various lawn care tasks.

One of the standout characteristics of the Poulan 401423 is its robust engine. It features a potent 40cc 2-cycle engine, providing ample power for cutting through thick grass, weeds, and brush. This engine design not only delivers impressive torque but also ensures a lightweight feel, allowing users to maneuver the equipment with ease. The engine is paired with a high-efficiency air filter that enhances performance and extends the equipment's lifespan by minimizing dust and debris intake.

In addition to its powerful engine, the Poulan 401423 features an adjustable cutting head that allows users to customize their cutting height based on the type of terrain and the desired lawn appearance. This feature is particularly beneficial for maintaining a pristine lawn, as it enables precise control over the grass length. The cutting head is also designed with a dual-line system that provides efficient trimming, helping to achieve a clean edge along sidewalks and flower beds.

Ergonomics is another key focus in the design of the Poulan 401423. The equipment is equipped with a comfortable, padded handle that reduces user fatigue, making it ideal for extended use. Additionally, it has a lightweight structure, which minimizes strain on the arms and back while working on landscaping projects.

Technology-wise, the Poulan 401423 incorporates anti-vibration technology, which significantly reduces vibrations felt by the user. This not only enhances comfort but also improves accuracy during operation, ensuring a more enjoyable lawn care experience.

Furthermore, the model features an easy-start mechanism, which allows for quick ignition with minimal effort. This is particularly useful for users who may struggle with traditional starting methods, ensuring that the equipment is ready to go when you are.

Overall, the Poulan 401423,96092000500 stands out as a powerful and efficient tool for outdoor maintenance. With its robust engine, adjustable cutting capabilities, ergonomic design, and innovative technology, it embodies the qualities that make it a top choice for anyone serious about lawn care. Whether tackling overgrown areas or fine-tuning the edges of your garden, this model successfully delivers on performance and user satisfaction.