Troy-Bilt 12180 Tiller Lubrication, Check for OIL Leaks, Check Hardware, Check Tire Pressure

Page 20

Section 5: Maintenance

WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.

TILLER LUBRICATION

Proper lubrication of the tiller is an essential part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1 and described below.

Use a good quality lubricating oil (#30 weight engine oil is suitable) and a good quality general purpose grease (grease that has a metal lubricant is preferred, if available).

•Remove wheels, clean wheel shaft (A, Fig. 5-1) and apply thin coating of grease to shaft.

•Grease back, front and sides of depth regulator lever (B, Fig. 5-1).

•Remove tines, clean tine shafts (C, Fig. 5-1) and inspect for rust, rough spots or burrs (especially around holes). File or sand smooth and coat ends of shaft with grease.

•Oil the threads on the handlebar height adjustment screws and the handlebar attaching screws (D, Fig. 5-1).

DB

AC

Figure 5-1

CHECK FOR OIL LEAKS

Before each use, check your tiller for signs of an oil leak – usually a dirty, oily accumulation either on the unit or on the floor where it has been parked.

A little seepage around a cover or oil seal is usually not a cause for alarm. However, if the oil drips overnight then immediate attention is needed as ignoring a leak can result in severe transmission damage.

If a cover is leaking, try tightening any loose screws. If the screws are tight, a new gasket or oil seal may be required. If the leak is from around a shaft and oil seal, the oil seal probably needs to be replaced. See your authorized dealer or contact the factory for service or advice.

IMPORTANT: Never operate the tiller if the transmission is low on oil. Check the oil level after every 30 hours of operation and whenever there is any oil leakage.

CHECK HARDWARE

Check for loose or missing hardware after every 10 operating hours. Tighten or replace hardware before using the tiller. Be sure to check the screws underneath the tiller hood (lift the hood flap) that secure the transmission cover and the depth regulator lever to the transmission.

CHECK TIRE PRESSURE

Check the air pressure in both tires. Deflate or inflate both tires evenly from 15-to-20 PSI (pounds per square inch). Be sure that both tires have the same air pressure or the unit will tend to pull to one side.

TRANSMISSION GEAR OIL SERVICE

Check the transmission gear oil level after every 30 hours of operation or whenever you notice any oil leak. Operating the tiller when the transmission is low on oil can result in severe damage.

A. To Check the Transmission

Gear Oil Level:

1.Check the gear oil level when the trans- mission is cool. Gear oil will expand in warm operating temperatures and this expansion will provide an incorrect oil level reading.

2.With the tiller on level ground, pull the Depth Regulator Lever all the way up.

3.Remove the oil fill plug (A, Fig. 5-2) from the transmission housing and look into the oil fill hole. You will see the main drive shaft on one side of the hole.

4.The gear oil level is correct if the gear oil is approximately halfway up the side of the drive shaft.

5.If the gear oil level is low, add gear oil as described next. If the gear oil level is okay, securely replace the oil fill plug.

IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmis- sion components.

6.If adding only a few ounces of gear oil, use API rated GL-4 or GL-5 gear oil having a viscosity of SAE 140, SAE 85W-

140or SAE 80W-90. If refilling an empty transmission, use only GL-4 gear oil having a viscosity of SAE 85W-140 or SAE 140.

7.While checking frequently to avoid

overfilling, slowly add gear oil into the oil fill hole until it reaches the halfway point on the drive shaft.

8.Securely replace the oil fill plug.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Broncotm 5 HP Table of Contents Safety TrainingKeep children and pets away Use slower engine speedsOperating Symbols To Avoid Serious InjuryAssembly Tools/Materials Needed for AssemblyLoose Parts List Qty. Description IntroductionAttach Handlebar Move Tiller Off Shipping PlatformPush the cable connector U, -4 up Cable adjuster X while preventingAdjuster from turning Screw R, -4Install Reverse Clutch Cable Check Level Transmission Gear OilCheck Hardware for Tightness Check Air Pressure in TiresFreewheel Features and ControlsWheel Drive Pins Forward Clutch Bail Reverse Clutch ControlTo Operate the Forward Clutch Bail To Operate the Reverse Clutch ControlHandlebar Height Adjustment Shallow Settings DeepTo Adjust the Handlebars Depth Regulator LeverOperation IntroductionBREAK-IN Operation Starting and Stopping the EngineOperating the Tiller Stopping the Tiller and Engine Turning the Tiller AroundFor reverse motion of the wheels and tines Let the tiller do the work Tilling depthsAvoid tilling soggy, wet soil Avoid making footprintsTilling across slopes without using terraces Clearing the tinesTilling on slopes Tilling up and down slopesPower Composting Loading and Unloading the TillerMaintenance Required Maintenance ScheduleProcedure EveryTransmission Gear OIL Service Tiller LubricationCheck for OIL Leaks Check HardwareRemoving a Tine Assembly Bolo TinesTine Inspection Removing a Single TineTo Check Forward Belt Tension Checking and AdjustingEngine Forward Clutch Bail Adjustment Replacement Belt InformationCheck belt tension after every 10 operating hours To Check Reverse Belt TensionEngine OIL Service Engine Cleaning AIR Cleaner ServiceSpark Plug Service CARBURETOR/GOVERNOR Control AdjustmentsTroubleshooting Tiller Weight Transmission Gear OIL SpecificationsFrame Weights Tiller LengthWarranty Service Customer Service and Technical ServiceReplacement Parts Engine Service and Repair1905362 3/99
Top Page Image Contents