Maxim MXR500 owner manual To Remove Belt Guard See Fig, To Replace Ground Drive Belt See Figs

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE BELT GUARD (See Fig. 27)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch (2.5 cm).

•Remove screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

BELT GUARD

SCREW

 

 

HEX NUT AND

 

WASHER

 

(LOCATED

 

BEHIND TIRE)

SCREW

HAIRPIN CLIP AND

 

CLEVIS PIN

FIG. 27

TO REPLACE GROUND DRIVE BELT (See Figs. 27 and 28)

•Remove belt guard as described in “TO REMOVE BELT GUARD”.

•Remove old belt by slipping off engine pulley first then remove from transmission pulley.

•Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

•Check belt adjustment as described below.

•Replace belt guard.

•Reposition wheel and replace clevis pin and hairpin clip.

GROUND DRIVE BELT ADJUSTMENT (See Fig. 28)

For proper belt tension, the extension spring should have about 5/8 inch (16 mm) stretch when drive control bar is in “ENGAGED” position. This tension can be attained as follows:

•Loosen cable clip screw securing the drive control cable.

•Slide cable forward for less tension and rearward for more tension until about 5/8 inch (16 mm) stretch is obtained while the drive control bar is engaged.

•Tighten cable clip screw securely.

CABLE CLIP

SCREW

ENGINE

PULLEY

DRIVE CONTROL CABLE

LESS

TENSION

MORE

5/8" TENSION

EXTENSION

SPRING

IDLERTRANSMISSION

PULLEYPULLEY

FIG. 28

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model NO. MXR500 HP 17 Inch Tiller Maintenance and Storage Safety RulesTraining PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Unpacking Carton See Fig Install Handle See Figs , 4,Connect Shift ROD See Fig Attach Clutch Cable See FigRemove Tiller from Crate Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation Tine Operation with Wheel Drive HOW to USE Your TillerForward Wheels ONLY/TINES Stopped Reverse Wheels ONLY/TINES StoppedTurning Before Starting EngineTo Transport ADD GasolineTilling Hints Tine Shear PinsTo Start Engine See Fig Cultivating Adjust Wheels for Cultivating See FigsLubrication Chart MaintenanceGeneral Recommendations Before Each USEAIR Filter See Fig EngineMuffler CleaningSpark Plug Cooling System See FigTo Adjust Handle Height See Fig Service and AdjustmentsTiller Tire CareTine Replacement See Figs , 25 To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTo Remove Belt Guard See Fig To Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILTroubleshooting Points Limited Warranty

MXR500 specifications

The Maxim MXR500 is a cutting-edge multi-channel audio mixer designed for professional sound engineers and musicians. Renowned for its robust construction and versatile features, the MXR500 is tailored for both studio recording and live performance settings. This mixer combines advanced technology with user-friendly controls, making it an ideal choice for a wide range of audio applications.

One of the standout features of the MXR500 is its exceptional sound quality. The mixer is equipped with high-performance preamps that ensure crystal-clear audio recording and playback. Each channel boasts a 3-band EQ, allowing users to finely tune the tonal characteristics of individual audio sources. This capability is particularly beneficial in live settings, where adjusting sound on the fly is crucial.

The MXR500 supports up to 16 input channels, facilitating the mixing of multiple audio signals simultaneously. Each channel offers independent gain control, allowing users to balance levels accurately. The mixer also features built-in digital effects, including reverb and delay, enhancing the audio experience without the need for additional equipment.

In terms of connectivity, the MXR500 comes with a range of input and output options, including XLR and TRS connectors. This versatility enables seamless integration with microphones, instruments, and other audio gear. Additionally, the mixer supports USB connectivity, making it easy to connect to computers for digital recording or live streaming.

The mixer’s interface is designed with ease of use in mind. Intuitive faders and knobs are clearly labeled, allowing sound engineers to make quick adjustments during performances. The bright LED meters provide visual feedback on audio levels, ensuring optimal mixing in various lighting conditions.

Durability is another hallmark of the Maxim MXR500. Constructed with high-quality materials, this mixer is built to withstand the rigors of both studio and on-the-road use. The compact design also makes it portable, ideal for musicians who need to transport their equipment frequently.

In conclusion, the Maxim MXR500 is a powerful and versatile audio mixer that meets the demands of professionals across different sectors. With its advanced features, exceptional sound quality, and durable construction, the MXR500 stands out as a reliable choice for any sound engineer or musician looking to elevate their audio production experience. Whether in the studio or on stage, the MXR500 delivers performance and quality that audio professionals can depend on.
Top Page Image Contents