Husqvarna TS200FR owner manual To Adjust Carburetor See Fig, Preliminary Setting, Final Setting

Page 11

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST CARBURETOR (See Fig. 11)

The carburetor has been preset at the factory and ad- justment should not be necessary.However, minor adjust- ments may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows.

In general, turning the adjust needles in (clockwise) de- creases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjust needles out (coun- terclockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: DAMAGE TO THE NEEDLES AND THE SEATS IN CARBURETOR MAY RESULT IF SCREWS ARE TURNED IN TOO TIGHT.

PRELIMINARY SETTING

•Air cleaner assembly must be assembled to the car- buretor when making carburetor adjustments.

•With engine off turn high speed adjust needle in (clockwise) closing it finger tight and then turn out (counterclockwise) 1-1/2 turns.

•Turn idle adjust needle in (clockwise) closing it finger tight and then out (counterclockwise) 1-1/4 turns.

FINAL SETTING

•Start engine and allow to warm for five minutes. Make final adjustments with engine running and tine clutch control lever in “DISENGAGED” position.

•With throttle control lever in “SLOW' position, turn idle adjust needle(clockwise) until engine begins to die then turn out (counterclockwise) until engine runs roughly.Turn needle to a point midway between those two positions.

•With throttle control lever in “FAST” position, turn high speed adjust needle.

IDLE RPM ADJUSTMENT-

•With engine at idle speed, turn the idle adjust screw slowly counterclockwise until the engine begins to falter.

•Then raise the engine speed by turning the idle ad- just screw clockwise until the engine holds a smooth constant speed.

ACCELERATION TEST -

•Move throttle control lever from “SLOW” to “FAST” position. If engine hesitates or dies, turn idle adjust needle out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine ac- celerates smoothly.

High speed stop is factory adjusted. Do not adjust or dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVER-SPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

FIG. 11

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Sleeve Hitch Tiller Attachment Model Number TS200FR Operation Maintenance and StorageTraining PreparationTable of Contents Attaching Tiller to Tractor AssemblyADD Gasoline HOW to USE Your TillerOperation Before Starting the EngineOperation DO’S and DON’TS To Start Tiller Engine See FigTilling CultivatingBefore Each USE Customer ResponsibilitiesGeneral Recommendations TillerLubrication AIR Filter Foam PRE-CLEANER See FigEngine Spark Plug CleaningCooling System See Fig MufflerTo Replace Belt See Fig Service and AdjustmentsTo Adjust Gauge Wheels To Adjust Belt See FigIdle RPM Adjustment To Adjust Carburetor See FigPreliminary Setting Final SettingEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine and Tines HP Tiller Attachment - Model Number TS200FRKEY Part Description Transmission and Gauge Wheels Repair Parts 02480

TS200FR specifications

The Husqvarna TS200FR is a high-performance, versatile machine designed for professional use in demanding environments. Known for its robustness and reliability, the TS200FR is a powerful tool that excels in various applications, including landscaping, grounds maintenance, and outdoor construction tasks. This track-driven, stand-on model provides exceptional stability and maneuverability, making it an ideal choice for operators seeking efficiency and comfort.

One of the standout features of the Husqvarna TS200FR is its powerful engine, which delivers impressive performance and torque. This engine enables the machine to tackle tough terrains and challenging tasks with ease. The reliable powertrain is designed to ensure consistent performance, allowing operators to maintain high productivity levels throughout their workday.

The TS200FR is equipped with advanced technologies that enhance its overall functionality. The patented All-Wheel-Drive system ensures optimal power distribution to all four wheels, providing superior traction on slippery or uneven surfaces. This feature is particularly beneficial when navigating steep inclines or wet conditions, minimizing the risk of slippage or loss of control.

Another key characteristic of the TS200FR is its user-friendly design. The intuitive controls are designed for ease of use, allowing operators to focus on their tasks without unnecessary distractions. The adjustable operator platform provides comfort during prolonged use, enabling users to operate the machine effectively without fatigue.

The machine also boasts a compact footprint, making it easy to maneuver in tight spaces. This is particularly advantageous for landscaping projects or urban environments where space can be limited. The durable construction of the TS200FR ensures that it can withstand the rigors of daily use, providing peace of mind for operators and businesses alike.

Maintenance is straightforward, thanks to the easily accessible components and clear service points. This design consideration minimizes downtime and enhances overall efficiency, allowing users to spend more time on the job rather than in the maintenance shop.

In summary, the Husqvarna TS200FR stands out as a powerful, reliable, and user-friendly machine suitable for a variety of demanding applications. Its robust engine, advanced traction technologies, and compact design make it an essential tool for professionals in landscaping and outdoor construction, ensuring high levels of productivity and operator satisfaction.
Top Page Image Contents