Bolens 675B manual Training, Preparation, Operation, Safety Alert Symbol

Page 3

SECTION 1: SAFETY

This machine meets voluntary safety stan- dard B71.8 – 1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National Standards Institute.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproduc- tive harm.

Safety Alert Symbol

This is a safety alert symbol. It is used in this manual and on the unit to alert you to potential hazards. When you see this symbol, read and obey the message that follows it. Failure to obey safety messages could result in personal injury or property damage.

Wheel Gear Lever

Reverse Clutch Control

Forward Clutch Lever

Recoil

Rope

Forward Clutch Lever

 

Starter

Depth

 

 

Regulator

 

Lever

Counter Rotating Tines

Figure 1-1

Training

1. Carefully read this Own- er’s Manual, the separate Engine Owner’s Manual,

and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the tiller. Never allow adults to operate the tiller with- out proper instruction.

3. Keep the area of operation clear of all persons, particularly children and pets.

4.Keep in mind that the operator or user is responsible for accidents or hazards occur- ring to other people, their property, and themselves.

Preparation

1.Thoroughly inspect the area where the tiller is to be used and remove all foreign objects.

2.Be sure all control levers are released

and the Wheel Gear Lever is in ENGAGE po- sition before starting the engine.

3.Do not operate the tiller without wearing adequate outer garments. Avoid loose gar- ments or jewelry that could get caught in moving parts.

4.Do not operate the tiller when barefoot or wearing sandals, sneakers, or light footwear. Wear protective footwear that will improve footing on slippery surfaces.

5.Do not till near underground electric cables, telephone lines, pipes or hoses. If in doubt, contact your telephone or utility company.

6.Warning: Handle fuel with care; it is highly flammable and its vapors are explosive. Take the following precautions:

a. Store fuel in containers specifically designed for this purpose.

b. The gas cap shall never be removed or fuel added while the engine is run- ning. Allow the engine to cool for sev- eral minutes before adding fuel.

c. Keep matches, cigarettes, cigars, pipes, open flames, and sparks away from the fuel tank and fuel container.

d. Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors. Use a funnel or spout to prevent spillage.

e. Replace all fuel tank and container caps securely.

f. If fuel is spilled, do not attempt to start the engine, but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.

7.Never make adjustments when engine is running (unless recommended by manu- facturer).

Operation

1. Do not put hands or feet near or under rotating parts.

2.Exercise extreme caution when on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine, remove the wire from the spark plug wire and prevent it from touching the spark plug, thoroughly inspect the machine for any damage, and repair the damage be- fore restarting and operating the machine.

4. Exercise caution to avoid slipping or fall- ing.

3

Image 3
Contents 13/04 Form no -00586B.fmTable of Contents Operation Safety Alert SymbolTraining PreparationUse slower engine speeds Maintenance and StorageTo Avoid Serious Injury Safety DecalsOperating Symbols Varioussymbolsshownhere,withworddescriptionsUnpacking Instructions For AssemblyIntroduction Inspect unitAttach the cable adjuster A, Figure Attach Reverse Clutch Control CableAttach Forward Clutch Control Cable Check Transmission Gear OIL Level Check AIRCheck Hardware Reverse Clutch Control Tiller FeaturesWheel Gear Lever Forward Clutch LeversRecoil Starter Handlebar Height AdjustmentEngine Controls Depth Regulator LeverStarting the Engine Pre-Start ChecklistIntroduction Break-In OperationOperating Tiller Stopping the EngineFor reverse motion of the wheels and tines To Change from High to Low Speed Changing Belt Range SpeedsStopping the Tiller and Engine To Change from Low to High SpeedAvoid Tilling Soggy, Wet Soil Tilling DepthsLet the Tiller Do the Work Avoid Making FootprintsTilling Up and Down Slopes Vertical Tilling Tilling On SlopesClearing the Tines Read the following recommendations before tilling on slopesCheck For Oil Leaks Transmission Gear Oil ServiceTiller Lubrication Check Tire Air PressureSpark Arrester Screen Service Engine Oil ServiceAir Cleaner Service Spark Plug ServiceThrottle Control Adjustment Wheel Gear Cable Adjustment Off Season StorageTines To Check and Adjust Tension on the Forward Drive Belt Checking And Adjusting Tension On Drive BeltsTo Check and Adjust Tension on the Re- verse Drive Belt Reinstall the belt cover and secure it with the two nutsForward Drive Belt Removal and Installation Installing the Forward Drive BeltRemoving the Forward Drive Belt Reverse Drive Belt Removal and Installation Installing the Reverse Drive BeltRemoving the Reverse Drive Belt Troubleshooting Parts List Description Model 675B25, Ref Model 675B GW-1124-2 GW-1714 Bearing, Tapered Roller with Race GW-1325C Model 675B TOP LEFT-HAND Tine Transmission 710-0599 OEM-290-254 Screws TROY-BILT Tiller Lifetime Limited Warranty