Bolens 675B manual Safety Decals, Operating Symbols, Varioussymbolsshownhere,withworddescriptions

Page 5

Safety Decals

For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2 be- low).

Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.

Refer to the Parts List in this manual for decal locations, part numbers and ordering instructions.

Control Description

(on Control Panel)

Tine Warning

Starting Stabilization

Message (on engine)

Warning Messages (on tine hood)

Hot Surfaces⁄Moving Belts

Warning (on belt cover)

Figure 1-2: Location of Safety and Operating Decals

	Operating Symbols					R
	Varioussymbols(shownhere,withworddescriptions)					R
	maybeusedonthetillerandengine.			CHOKE	CHOKE	REVERSE
	NOTE:Yourunitmaynothaveallofthesymbols.			CHOKE	CHOKE	REVERSE
	NOTE:Yourunitmaynothaveallofthesymbols.			ON	OFF
						ROTATING TINES
	FAST	SLOW	STOP	TILLER DIRECTION		LEVER DIRECTION

WARNING

TO AVOID SERIOUS INJURY:

•READ THE OPERATOR’S MANUAL.

•KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS.

•KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

•NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

•SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UN- CLOGGING TINES OR MAKING REPAIRS.

•KEEP BYSTANDERS AWAY FROM MACHINE.

•KEEP AWAY FROM ROTATING PARTS.

•USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

5

Image 5

Contents 13/04 Form no -00586B.fmTable of Contents Training Safety Alert SymbolPreparation OperationUse slower engine speeds Maintenance and StorageOperating Symbols Safety DecalsVarioussymbolsshownhere,withworddescriptions To Avoid Serious InjuryIntroduction For AssemblyInspect unit Unpacking InstructionsAttach Forward Clutch Control Cable Attach the cable adjuster A, FigureAttach Reverse Clutch Control Cable Check Hardware Check Transmission Gear OIL LevelCheck AIR Wheel Gear Lever Tiller FeaturesForward Clutch Levers Reverse Clutch ControlEngine Controls Handlebar Height AdjustmentDepth Regulator Lever Recoil StarterIntroduction Pre-Start ChecklistBreak-In Operation Starting the EngineFor reverse motion of the wheels and tines Operating TillerStopping the Engine Stopping the Tiller and Engine Changing Belt Range SpeedsTo Change from Low to High Speed To Change from High to Low SpeedLet the Tiller Do the Work Tilling DepthsAvoid Making Footprints Avoid Tilling Soggy, Wet SoilClearing the Tines Tilling On SlopesRead the following recommendations before tilling on slopes Tilling Up and Down Slopes Vertical TillingTiller Lubrication Transmission Gear Oil ServiceCheck Tire Air Pressure Check For Oil LeaksAir Cleaner Service Engine Oil ServiceSpark Plug Service Spark Arrester Screen ServiceTines Throttle Control Adjustment Wheel Gear Cable AdjustmentOff Season Storage To Check and Adjust Tension on the Forward Drive Belt Checking And Adjusting Tension On Drive BeltsTo Check and Adjust Tension on the Re- verse Drive Belt Reinstall the belt cover and secure it with the two nutsRemoving the Forward Drive Belt Forward Drive Belt Removal and InstallationInstalling the Forward Drive Belt Removing the Reverse Drive Belt Reverse Drive Belt Removal and InstallationInstalling the Reverse Drive Belt Troubleshooting Parts List Description Model 675B25, Ref Model 675B GW-1124-2 GW-1714 Bearing, Tapered Roller with Race GW-1325C Model 675B TOP LEFT-HAND Tine Transmission 710-0599 OEM-290-254 Screws TROY-BILT Tiller Lifetime Limited Warranty