Bolens 675B manual GW-1124-2

Page 28

MODEL 675B

NOTE 1: These screws are a special sealing screw that cannot be reused without risking the loss of transmission oil. If these screws are loosened or removed, they must be replaced with new screws.

	REF	PART NO.	DESCRIPTION	REF	PART NO.	DESCRIPTION
	NO.	PART NO.	DESCRIPTION	NO.	PART NO.	DESCRIPTION
	NO.			NO.

	1	721-04031	Oil Seal	12	710-04049	Hex Flange Screw, 5/16-18 x 5/8*
	2	1105620	Pipe Plug, 1/4	13	GW-20873	Tiller Housing Cover, left side
	3	721-04001	Seal, Transmission Bore	14	GW-1129-1	Gasket, Tiller Housing Cover,.010" (A/R)
	4	710-04043	Hex Flange Screw, 5/16-18 x 3/4*	15	1915069	Self-Sealing Screws, 1/4-20 x 7/8
	5	1983632	Oil Seal, Input Pinion Shaft1	16	GW-1115	Rear Bearing Cap
	6	GW-20910	Transmission Cover (Incl. four Ref. 18)	17	GW-1124-2	Gasket, Rear Bearing Cap,.010" Thick (A/R)
	7	GW-20694	Gasket, Transmission Top Cover	18	GW-90063	Hex Flange Screw, 5/16-18 x 1*
	8	619-04010	Transmission Case Assy.	19	1915068	Self-Sealing Screws, 1/4-20 x 5/8
	9	GW-9467	Plug	21	736-0169	Lock washer, 3/8
	10	1917101	Mounting Plate, Wheel Clutch Cable	22	710-0216	Hex Hd. Screw, 3/8-16 x 3/4*
	11	721-04035	Oil Seal, Tiller Shaft	—	737-0353†	Oil, 85W-140

*Specify GRADE 5 if ordering part locally. A⁄R – As Required

*Capacity of transmission is 53 oz.

28

Image 28

Contents Form no -00586B.fm 13/04Table of Contents Safety Alert Symbol TrainingPreparation OperationMaintenance and Storage Use slower engine speedsSafety Decals Operating SymbolsVarioussymbolsshownhere,withworddescriptions To Avoid Serious InjuryFor Assembly IntroductionInspect unit Unpacking InstructionsAttach Reverse Clutch Control Cable Attach the cable adjuster A, FigureAttach Forward Clutch Control Cable Check AIR Check Transmission Gear OIL LevelCheck Hardware Tiller Features Wheel Gear LeverForward Clutch Levers Reverse Clutch ControlHandlebar Height Adjustment Engine ControlsDepth Regulator Lever Recoil StarterPre-Start Checklist IntroductionBreak-In Operation Starting the EngineStopping the Engine Operating TillerFor reverse motion of the wheels and tines Changing Belt Range Speeds Stopping the Tiller and EngineTo Change from Low to High Speed To Change from High to Low SpeedTilling Depths Let the Tiller Do the WorkAvoid Making Footprints Avoid Tilling Soggy, Wet SoilTilling On Slopes Clearing the TinesRead the following recommendations before tilling on slopes Tilling Up and Down Slopes Vertical TillingTransmission Gear Oil Service Tiller LubricationCheck Tire Air Pressure Check For Oil LeaksEngine Oil Service Air Cleaner ServiceSpark Plug Service Spark Arrester Screen ServiceOff Season Storage Throttle Control Adjustment Wheel Gear Cable AdjustmentTines Checking And Adjusting Tension On Drive Belts To Check and Adjust Tension on the Forward Drive BeltReinstall the belt cover and secure it with the two nuts To Check and Adjust Tension on the Re- verse Drive BeltInstalling the Forward Drive Belt Forward Drive Belt Removal and InstallationRemoving the Forward Drive Belt Installing the Reverse Drive Belt Reverse Drive Belt Removal and InstallationRemoving the Reverse Drive Belt Troubleshooting Parts List Model 675B Description25, Ref Model 675B GW-1124-2 GW-1714 Bearing, Tapered Roller with Race GW-1325C Model 675B TOP LEFT-HAND Tine Transmission 710-0599 OEM-290-254 Screws TROY-BILT Tiller Lifetime Limited Warranty