Bush Hog RTS manual Section Preparation for USE, Attaching to Tractor

Page 8

SECTION II

PREPARATION FOR USE

2-1 ATTACHING TO TRACTOR

WARNING

TO AVOID SERIOUS INJURY OR DEATH: NEVER STAND BETWEEN TRACTOR AND TILLER WHILE TRACTOR IS BEING BACKED TO HITCH.

WARNING

TO AVOID SERIOUS INJURY OR DEATH: ADDITIONAL TRACTOR FRONT BAL- LAST MAY BE NEEDED FOR STABLE OPERATION AND TRANSPORT OF THE TILLER. SEE TRACTOR OPERATOR’S MANUAL FOR RECOMMENDED WEIGHTS.

A. Attach tiller to tractor 3-point hitch per tractor operator’s manual. Do not attach driveline at this time.

NOTE

Due to the many variations in tractor/implement hitch points and corresponding differences in distances between tractor PTO shafts and implement input shafts, drivelines may need to be shortened as described in the following steps:

B. Raise and lower tiller to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor, leaving tiller in position of shortest distance. Securely block tiller in position.

C. Pull driveline apart. Attach outer (female) sec- tion to tractor PTO shaft. Pull on driveline section to be sure that yoke locks into place.

D. Hold driveline sections parallel to each other to determine if it is too long. Each section should end approximately 3 inches (76mm) short of reaching universal joint shield on opposite section. If too long, measure 3 inches back from universal joint shield and mark on opposite section. (Figure 2-1). Do this for both sections.

E. Raise and lower tiller to determine position with greatest distance between PTO shaft and gear- box input shaft. Shut down tractor leaving tiller in position of greatest distance. Securely block tiller in position.

F. Hold driveline sections parallel to each other and check for minimum 6 inches (15cm) overlap. (Figure 2-2) If driveline has been marked for cutting, overlap will be the distance between two marks. If driveline has less than minimum overlap, do not use. Contact authorized Bush Hog dealer.

NOTE

If driveline is correct length, omit the follow- ing steps “G” through “J” and proceed to step “K”.

G. Clamp driveline in a padded vice to prevent damage to shield. Cut of shield where marked. (Figure 2-3)

Figure 2-1

Figure 2-2

Minimum Overlap

Figure 2-3

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Bush HOG Congratulations Table of Contents Retail CUSTOMER’S Responsibility Under the Bush HOG WarrantyThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Rotary TillersImportant Safety Precautions Technical Specifications Section Introduction and DescriptionIntroduction DescriptionSection Preparation for USE Attaching to TractorOffsetting Tiller Hitch Lug Dimension Clamp Bolts Frame GearboxSection Operating Instructions General SafetyAdjusting for Work Section Maintenance Maintenance Check ListOperation TransportingBondioli & Pavesi Driveline Binacchi DrivelineBlade Replacement Bolt ReplacementSlip Clutch Adjustment Slip Clutch Operational CheckTroubleshooting Section Dealer AssemblyTroubleshooting Exploded Assembly Safety Decals Torque Specifications Recommended Torque in Foot Pounds Newton MetersEMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsThis Act Seeks Osha Regulations

RTS specifications

The Bush Hog RTS series is a standout line of rotary tillers designed for both performance and durability, making it an ideal choice for agricultural, landscaping, and gardening applications. Built to meet the demanding needs of professional landscapers and dedicated gardeners, the RTS offers several key features and advanced technologies.

One of the most noteworthy aspects of the Bush Hog RTS is its robust construction, which leads to enhanced longevity and reliability. The frame is heavily reinforced to withstand tough operating conditions, while the tiller tines are crafted from high-quality materials, ensuring they maintain their sharpness and effectiveness even after extensive use. This durability translates to lower maintenance costs and reduced downtime, crucial for maintaining productivity.

In terms of performance, the RTS series stands out with its impressive tilling depth and width capabilities. Users can achieve a maximum tilling depth that allows for effective soil aeration, promoting root growth and improving overall soil health. The width options available in the RTS lineup provide flexibility, catering to various field sizes and types of landscaping projects.

The Bush Hog RTS also incorporates advanced technology to enhance ease of use. The adjustable side runners enable users to control the tilling depth precisely, while built-in gearbox systems allow for smooth power transfer, ensuring consistent performance while reducing wear and tear on the machine.

Another significant feature is the chain-driven design that promotes efficient power usage and minimizes slippage. This results in a more reliable operation, especially in challenging soil conditions. Furthermore, the RTS series is compatible with a variety of tractor models, making it a versatile addition to any equipment fleet.

To maximize operator comfort and efficiency, the RTS features an ergonomic design, enabling easy attachment and detachment to tractors. The simple controls and straightforward operation make it accessible for users of all skill levels, reducing the learning curve for new operators.

Overall, the Bush Hog RTS rotary tillers combine strength, versatility, and innovative features, positioning them as a top choice for those looking to enhance their land management and agricultural productivity. With their superior construction and performance, the RTS series stands ready to tackle soil preparation tasks of any scale with ease and effectiveness.
Top Page Image Contents