Craftsman 917.293301 To Remove Wheel, To Remove Belt Guard, To Replace Ground Drive Belt

Page 16

TiRE CARE

,_,CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

o Maintain 20 pounds of tire pressure. If tire pressures are not equal, tiller will pull to one side.

. Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL

o Place blocks under transmission to keep tiller from tipping.

o Remove outer side shield by removing nuts "A" and "B".

o Remove inner side shield by removing nuts "C" and "D".

o Remove hairpin clip and clevis pin from wheel.

o Remove wheel and tire.- Repair tire and reassemble.

Clevis

t _

¢

Hairpin

Clip

Nut "B"

inner Side Shield

Nut -A,,/'f- Outer Side Shield

TO REMOVE BELT GUARD

NOTE: For ease of removal, remove hair-

pin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

°Remove two (2) cap nuts and washers from side of belt guard.

°Remove hex nut and washer from bot- tom of belt guard (located behind wheel).

°Pull belt guard out and away from unit. = Replace belt guard by reversing above

procedure.

Hex Nut and

Be_tGuard Washer

(Located

ind Tire)

Cap Nut _ ___\_

and z%_j\_ I

Washer Hairpin'Clip and Clevis Pin

TO REPLACE GROUND DRIVE BELT

=Remove belt guard as described in 'q'o

REMOVE BELT GUARD".

Loosen belt guides "A" and "B" and also remove stud "C"=

°Remove old belt by slipping off engine pulley first then remove from the pulley.

Place new belt in groove of transmis-

sion pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF

IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

oTighten belt guides '%"and "B" and stud

"C".

o Check belt adjustment as described below°

o Replace belt guard.

°Reposition wheel and replace clevis pin and hairpin clip.

GROUND DRIVE BELT ADJUST-

MENT

For proper belt tension, the extension

spring should have about 5/8 inch stretch when drive control bar is in "ENGAGED"

position. This tension can be attained as follows:

-Loosen cable clip screw securing the drive control cable.

o Slide cable forward for less tension and rearward for more tension until about 5/8 inch stretch is obtained while the drive

control bar is engaged.

o Tighten cable clip screw securely.

16

Image 16
Contents Tille SEARS, Roebuckand CO., D/817WA, Hoffman ESTATES, IL Limited TWO Year Warranty on Craftsman TillerPreparation Operation Maintenance and StorageOther reproductive harm Spark Plug Maintenance AgreementCustomer REESPONSgBILITllES Contents of Hardware Pack Viewed from r.h. side of tiller Handie Lock Unpacking CartonPivot Bolt Remove Tiller from Crate CheckConnect Shift ROD Handle HeightShift Lever Indicator Shows which Choke Control Used when starting a cold engineKnow Your Tiller Shift Lever Used to shift transmissionDepth Stake ToppingINE Operation with Wheel Rive Orward Wheels ONLY/TINES ToppedTurning Outer Side ShieldsAround the Yard Around TownTo Start Engine Tilling HintsOO1 OIO Tine SHF.AR PunsMaintenance Schedule 3ENERAL RecommendationsEfore Each USE UbricationTo Service PRE-CLEANER To Service CartridgeEngine AIR FilterTo Adjust Handle Height Cooling SystemMuffler Spark PlugGround Drive Belt Adjust To Remove WheelTo Remove Belt Guard To Replace Ground Drive BeltIine Replacement To Adjust Throttle Control Cable To Adjust CarburetorIDLE RPM Adjustment Acceleration TestTtLLER Fuel SystemEngine OIL CylinderProblem Problemcause Correction Tiller -- Model Number Handles 148583MAINFRAME, Left Side Taller - Model Number74930588 Tbller - Model Number ScrewTiller - Model Number 150698106211X 4895H1618 Tine Shield161415X574 TiNE Assembly 44593132673 74610616Decals Decal,Caution, DriveControlTaller - Model Number To INSTALl. see Repair Tbller =- Model Huber104 634ENGINE, Briggs & Stratton - Model Number 1302, Type no -E1 Tiller -- Model Number 399268Flywheel Kit163 164 3O0 304 305333 335 347 356 356APage Para pedir servicio de reparacibn a domicilio Para ordenar piezas con enrega a domicilioCall 24 hours a day, 7 days a week