EarthQuake MODEL 3365CE Unpacking and Assembly, Do not TRY to Lift the Rototiller from the Carton

Page 7

OPERATor INSTRUCTIONS and parts

Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE

Unpacking and Assembly

unpack tiller & assemble

1.Open top of carton and remove handlebar assembly.

2.Find parts packet. Parts packet for 3365/3365B/3365K/3365CE contains:

6- 5/16-18 x 1-3/4” bolts

6- 5/16” spring lockwashers

2- hand knobs

4- locknuts

2- 1/2” push nuts

1- detent pin

Parts packet for 3365PS/3365KPS/R3365H/3365PSCE con- tains:

2- 3/8-16 x 1” bolts

2- 3/8-16 biway locknuts

2- 5/16-18 x 1” bolts

4- 5/16-18 x 1-3/4” bolts

6- 5/16” spring lockwashers

2- hand knobs

4- 5/16” locknuts

2- 1/2” push nuts

1- detent pin

3.Cut open end of carton and remove machine:

a.Install wheels on each end of axle; tap on push nuts with a hammer.

b.Assemble tines to unit, inside tines first. Sharp edge of tine will be away from operator at top, or face down at front of machine.

c.Outside tines have two positions- wide 21” and narrow 16”. For narrow width, assemble with short side of tine holder pipe towards center of machine.

d.For wide width, move the left tine to the right side and right tine to the left side. Assemble with the long half of tine pipe towards machine.

e.Slide the top handle of handlebar over the lower loop. Put 5/16-18 x 1-3/4” bolts through both holes from inside out; put on 5/16” spring lockwashers and tighten with hand knobs. Models 3365PS, 3365KPS, and R3365H will use 3/8-16 x 1” bolts with nuts and 5/16-18 x 1”

bolts with hand knobs. See parts explosion on page 19.

f.Check upper and lower jam nuts for tightness. See page 9, Belt Tension Adjustment.

g.Add and check engine oil.

install depth regulator lever

1.Install the depth regulator lever through hole in bracket from the bottom up with curve to rear of unit and secure with detent pin.

Fill engine CRANKCASE

1.Add oil according to engine manual.Do not overfill. Use a clean, high quality detergent oil.Container must be marked A.P.I.Service SF - SJ. Use no special additives with recommended oils. Do not mix oil with gasoline. Oil level must be full. Check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening.

2.Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use.

800-345-6007

IMPORTANT

The right and left sides ofyour rototiller are determined from the operating position as you face the direction of forward travel.

Engine is shipped from factory without oil.You must add engine oil before starting engine.

!CAUTION

DO NOT TRY TO LIFT THE ROTOTILLER FROM THE CARTON.

narrow tine width

wide tine width

upper

handlebar

lower

handlebar

loop

hand knob

depth

regulator

lever

detent pin

Page

GetEarthquake.com

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operating Instructions Page Introduction ContentsPreparation Important Safety PrecautionsOWNER’S Responsibility Special MessagesOperation Maintenance and storageLBLCENOISE80 Safety DecalsTines DANGER/OPERATION Hood WarningDo not TRY to Lift the Rototiller from the Carton Unpacking and AssemblyTransport Position Operating Position Features 3365/3365B/3365Ce/3365KControls Drive Safety Control LeverBelt Tension Adjustment Engine should be OFF Before Adjusting ANY ControlsYOU Must ADD Engine OIL Before Starting Engine OperationPRE-START Inspection START-UPTilling For models R3365H and 3365PSCE onlyOperating Speed Shutting DownMaintenance Operation Before Hours or Maintenance ScheduleServicing the Rototiller Check Belt Tension Belt replacementChange Forward Belt Lubrication Engine MaintenanceClean tine axle shaft Check or Fill Engine CrankcasePrepare for Storage StorageTroubleshooting Guide Troubleshooting and RepairDescription QTY 3365/3365B/3365ce/3365K Handlebar parts3365PS/3365KPS Handlebar parts R3355H/3365PSCE Handlebar parts 3365KPS Bumper Model 3365PS/3365PSCE Bumper Guard Parts SHIELD, DirtModel R3355H Bumper R3355H motor mount & Hood partsModel R3355H Bumper Guard Parts NUT, Nyloc 1/4 Tines & transmission PartsFront Tine Rototillers Year Limited Warranty Terms and ConditionsOPERATor Instructions and parts OPERATor Instructions and parts Benefit you throughout the year

MODEL 3365CE, 3365, 3365B, 3365PSCE, MODEL 3365KPS specifications

The EarthQuake MODEL 3365KPS, 3365PSCE, 3365, MODEL 3365CE, and MODEL 3365PS represent a line of robust and powerful tools designed to meet various construction and landscaping needs. These models are engineered to provide exceptional performance in the most challenging conditions, making them a favorite among professionals and DIY enthusiasts alike.

A standout feature of these models is their heavy-duty construction. Built with high-quality materials, the EarthQuake 3365 series ensures durability and longevity, capable of withstanding the rigors of daily use. They are particularly known for their efficient combustion engines that deliver robust power while maintaining fuel efficiency, allowing users to operate for extended periods without frequent refueling.

One of the key technologies incorporated into the EarthQuake 3365 models is their precision-engineered vibration reduction system. This innovation minimizes operator fatigue during prolonged use, enhancing comfort and productivity on the job. Additionally, the models are equipped with an easy-start mechanism that simplifies ignition, ensuring a hassle-free start every time.

The EarthQuake 3365 series also features adjustable settings that provide versatility for various applications. Whether for digging, tamping, or breaking concrete, these tools can adapt to specific tasks efficiently. The pneumatic wheels on the models enhance mobility, making it easy to maneuver them across different terrains, including rough and uneven surfaces.

Another characteristic that sets the EarthQuake 3365 line apart is its user-centric design. Each model is equipped with ergonomic handles that promote a comfortable grip, allowing for better control and precision during operation. Safety features, such as automatic shut-off mechanisms and protective guards, are also integrated to ensure that users can operate the tools confidently and with reduced risk of accidents.

In summary, the EarthQuake MODEL 3365KPS, 3365PSCE, 3365, MODEL 3365CE, and MODEL 3365PS represent the pinnacle of engineering in construction tools. With their powerful engines, durable construction, user-friendly features, and advanced technologies, these models are ideal for both commercial and residential applications, offering reliable performance and unmatched efficiency for all your tough jobs.
Top Page Image Contents